DELAIR UX11 Скачать руководство пользователя страница 58

Страница: 58 / 94

User Manual UX11

At the takeoff location, hold the aircraft by the right wing with your right hand (or hold the aircraft

by the left wing with your left hand).

CAUTION

Make sure the propeller is clear from objects or body parts at all times during the takeoff procedure.

Press the

Confirm

button on the aircraft for a few seconds until the motor beeps.

The motor is initialized, propellers stay still,

TAKE OFF

LED is blinking green rapidly.

Note

As a safety measure, if you do not proceed to next step in 15 seconds, the motor will automatically

deactivate. You can also manually deactivate the motor by using the ABORT button on

Delair Flight

Deck

. If the motor was deactivated (automatically or manually) it may be initialized again as per text

above.

Hold the aircraft horizontally and against the wind, and make sure your take-off direction is free

of obstacles (adjust if necessary). Then press the

Confirm

button again (short push). The elevons

move up indicating the aircraft is ready for takeoff. The

TAKE OFF

LED is steady green (if elevons

does not move or

TAKE OFF

LED is blinking red, please contact support).

Tilt the aircraft with its nose up at an upwards angle of 30°. After 1.5 seconds, the motor runs at

full speed.

Note

To abort the takeoff and stop the motor, hold the aircraft vertically with its nose pointing upwards for

1 second or press the

Confirm

button. If takeoff was aborted you may resume and re-initiate takeoff

without starting over the entire procedure.

Throw the aircraft in a forward and upward motion.

Note

Avoid to give the aircraft a rotating motion while throwing.

The UX11 aircraft takes off.

Delair

676, Rue Max Planck – 31670 Toulouse-Labège, France

Tel: +33 (0) 5 82 95 44 06

| www.delair.aero

Capital: 238 110,30 € - APE: 3030Z – Intra-Community VAT number: FR90 53 09 69 781 – 530 969 781 R.C.S. Toulouse

This document is the sole property of Delair and cannot be used or reproduced without the written authorization of Delair.

Содержание UX11































































































Результаты поиска

Содержание UX11

Отзывы:

DELAIR UX11, Руководство пользователя, Страница: 58 / 94

Результаты поиска

Содержание UX11

Отзывы: