DELAIR UX11 Скачать руководство пользователя страница 4

Страница: 4 / 94

User Manual UX11

General caution

Keep this manual accessible, so you can refer to it at any time.
The information and specifications included in this publication were in effect at the time of approval

for printing. Delair reserves, however, the right to make changes to specifications and product

descriptions contained in this document at any time without notice and without incurring any

obligation whatever.

A few words about safety

Your safety and the safety of others is very important, and using this aircraft safely is an important

responsibility.
To help you make informed decisions about safety, we have provided operating procedures and other

information on labels and in this manual. This information alerts you of potential hazards that could

hurt you or others.
Of course, it is not practical or possible to warn you about all the hazards associated with operating

or maintaining an aircraft. You must use your own good judgment. This entire book is filled with

important safety information—please read it carefully.

Avoid rotating propellers

Rotating propellers can cause serious cuts and even amputate fingers. Keep away from the propeller

whenever you are handling the aircraft. If you find it necessary to work on the propeller always remove

the battery first.
A long press on the aircraft

Power

button will deactivate the motion of the propellers.

Battery warning

Do not use any other battery or charger than the ones delivered with the system. The use of an

unqualified battery or charger may present a risk of fire, explosion, leakage or other hazard.

Stay away from hot parts

The UX11 heatsink and Delair Link metallic casing can become very hot during operation and remain

hot for a while after stopping. Contact with these parts can cause burns. Always be very cautious when

handling them.

Keep the operating area clear

The pilot is responsible of the security of people and animals that are in the operating area. Always

make sure that the area is clear before attempting any takeoff or landing operation (for details, see

Obstacle clearances on page 22

Delair

676, Rue Max Planck – 31670 Toulouse-Labège, France

Tel: +33 (0) 5 82 95 44 06

| www.delair.aero

Capital: 238 110,30 € - APE: 3030Z – Intra-Community VAT number: FR90 53 09 69 781 – 530 969 781 R.C.S. Toulouse

This document is the sole property of Delair and cannot be used or reproduced without the written authorization of Delair.

iii

Содержание UX11































































































Результаты поиска

Содержание UX11

Отзывы:

DELAIR UX11, Руководство пользователя, Страница: 4 / 94

Результаты поиска

Содержание UX11

Отзывы: