DELAIR UX11 Скачать руководство пользователя страница 32

Страница: 32 / 94

User Manual UX11

From 50 m (164 ft) to 280 m (919 ft) in the launch direction, no obstacles may be present above

the safety area determined by a 15° angle and within 25 m (82 ft) to the left and right of the launch

direction.

50 m

60 m

15 m

15 °

Flight

No obstacles may be present in an area of 15 m (49 ft) below the cruise flight height and connections

(between take-off/landing and flight area). The

Elevation graph

must be used to visualize altitude

above terrain along the complete flight plan.

15 m

Delair

676, Rue Max Planck – 31670 Toulouse-Labège, France

Tel: +33 (0) 5 82 95 44 06

| www.delair.aero

Capital: 238 110,30 € - APE: 3030Z – Intra-Community VAT number: FR90 53 09 69 781 – 530 969 781 R.C.S. Toulouse

This document is the sole property of Delair and cannot be used or reproduced without the written authorization of Delair.

Содержание UX11































































































Результаты поиска

Содержание UX11

Отзывы:

DELAIR UX11, Руководство пользователя, Страница: 32 / 94

Результаты поиска

Содержание UX11

Отзывы: