Daikin FTKE25BVM Скачать руководство пользователя страница 254

Страница: 254 / 298

Si12-411A

Outdoor Unit (50 / 52 / 58 / 68 / 75 Class)

Removal Procedure

243

2.2

Removal of

Electrical BOX

Procedure

Warning

Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.

Step

Procedure

Points

1. Removing the tie wires

Remove the piping in the
backward direction.

The figure shows the tie
pipe connections.

Remove the terminal
board fitting screw.

Match the colours of the tie
wires to A, B, C and D ports
as follows.
(1) - Black Power
(2) - White Power
(3) - Red Transmission

Wires are fixed to the
terminal board with screws.

Terminal board is made of
integral moulded resin.

Содержание FTKE25BVM











































































































































































































































































































Результаты поиска

Содержание FTKE25BVM

Отзывы:

Бренды по названию

Популярные бренды

Daikin FTKE25BVM, Руководство по обслуживанию

Результаты поиска

Содержание FTKE25BVM

Отзывы:

Бренды по названию

Популярные бренды