Daikin FTKE25BVM Скачать руководство пользователя страница 210

Страница: 210 / 298

Si12-411A

Troubleshooting

Service Diagnosis

199

Troubleshooting

Check No.6

Refer to P.209

Check No.7

Refer to P.210

Check No.9

Refer to P.211

Turn off the power and turn it on
again to get the system started.

heck No.

Check the thermistor resistance
value.

Replace the fin thermistor.

Check the power transistor
and fin for looseness. If
they are found to be fit
tightly, replace the PCB or
the power transistor.

Replace the fan motor.
Correct the connectors and
fan motor leads.
Replace the outdoor unit
PCB.

Clean up the radiation fin.

(R2851)

Caution

Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.

Error displayed again?

YES

Slightly dirty

Check No. 9

Check the outdoor unit

fan or related.

Malfunctioning

Radiation fin dirty?

Too dirty

Functioning

Thermistor as

specified in its characteristic

chart?

Above 90˚C?

YES

Fin thermistor

Check the radiation fin
temperature.

heck No.

Check the installation condition.

Содержание FTKE25BVM











































































































































































































































































































Результаты поиска

Содержание FTKE25BVM

Отзывы:

Бренды по названию

Популярные бренды

Daikin FTKE25BVM, Руководство по обслуживанию

Результаты поиска

Содержание FTKE25BVM

Отзывы:

Бренды по названию

Популярные бренды