Daikin FTKE25BVM Скачать руководство пользователя страница 184

Страница: 184 / 298

Si12-411A

Troubleshooting

Service Diagnosis

173

Troubleshooting

Check No.6

Refer to P.209

Note:

If the outside temperature is below –10°C in the cooling mode, the system may get interrupted
with error

displayed. The system will be reset itself, but this stop will be put in the error history

memory.

Check No. 6

Indoor unit heat exchanger
thermistor check

Check the intake air filter.

Check the air passage.

YES

(R1401)

Check the dust accumulation on
the indoor unit heat exchanger.

YES

Is there any

short-circuit?

Is it very dirty?

Does it conform to

the thermistor characteristic

chart?

Provide sufficient air passage.

Clean the air filter.

Clean the heat exchanger.

Replace the indoor unit PCB.

Replace the thermistor
(replace the indoor unit PCB).

Caution

Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.

Содержание FTKE25BVM











































































































































































































































































































Результаты поиска

Содержание FTKE25BVM

Отзывы:

Бренды по названию

Популярные бренды

Daikin FTKE25BVM, Руководство по обслуживанию

Результаты поиска

Содержание FTKE25BVM

Отзывы:

Бренды по названию

Популярные бренды