Daikin FTKE25BVM Скачать руководство пользователя страница 185

Страница: 185 / 298

Troubleshooting

Si12-411A

174

Service Diagnosis

5.5

Fan Motor or Related Abnormality

5.5.1

AC Motor

Remote
Controller
Display

Method of
Malfunction
Detection

The rotation speed detected by the

Hall IC

during fan motor operation is used to determine

abnormal fan motor operation.

Malfunction
Decision
Conditions

When the detected rotation speed is less than 50% of the HH tap under maximum fan motor
rotation demand.

Supposed
Causes

Operation halt due to short circuit inside the fan motor winding.

Operation halt due to breaking of wire inside the fan motor.

Operation halt due to breaking of the fan motor lead wires.

Operation halt due to faulty capacitor of the fan motor.

Detection error due to faulty control PCB.

Troubleshooting

Check No.16

Refer to P.215

Rotate the fan by hand.

Check No. 16

Check Hall IC

Operate the fan.

Does it rotate?

Does it rotate smoothly?

Is there an output?

Is it at the rated voltage?

∗

Is there conductivity?

Check the capacitor's
conductivity

Check the fan motor voltage.
(immediately after re-start)

Is it at the rated voltage?

∗

Check the fan motor voltage.

YES

Replace the fan motor or control
PCB.

Replace the fan motor

Replace control PCB.

Replace the fan motor.

Replace the control PCB.

∗

Measure the voltage between

the red and black lead wires of
the fan motor, and check if the
maximum voltage reaches the
rated voltage.

Replace the capacitor.
(Replace the control PCB.)

Replace the fan motor.

(R3219)

Caution

Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.

Содержание FTKE25BVM











































































































































































































































































































Результаты поиска

Содержание FTKE25BVM

Отзывы:

Бренды по названию

Популярные бренды

Daikin FTKE25BVM, Руководство по обслуживанию

Результаты поиска

Содержание FTKE25BVM

Отзывы:

Бренды по названию

Популярные бренды