Curtiss-Wright R-NET, Техническое руководство

Страница: 62 / 206

Curtiss-Wright | PG Drives Technology
SK77981-14
62 | R-net Technical Manual | Chapter 3 – Programming
*Actuator Endstop Bleep Sets whether there is a bleep when a seat axis reaches endstop
*Sounder Volume Sets volume of audible feedback from JSM
*Lock Function Enabled Sets how the lock function is activated
*Reverse Driving Alarm Sets if the reverse driving alarm is active
*Emergency Stop Switch Allows latched operation without the use of an Emergency Stop switch
OBP Keycode Entry Sets the method of entry of OBP
*Power-up Mode Sets the Mode that will be active when the system is powered-up
External Profile Jack Function Sets which type of external input is to be connected to the system
Actuator Switches while Driving Sets whether seating adjustment is permitted while the wheelchair is driving
Start Up Beep Sets whether a short beep occurs when the control system is powered -up
Profile/Mode Jack Detect Sets whether the CJSM2 performs error checking on the connected switch
On/Off Jack Detect Sets whether the CJSM2 performs error checking on the connected switch
Joystick
*Joystick Forward Throw Sets the amount of joystick movement required to reach full speed in this direction
*Joystick Reverse Throw Sets the amount of joystick movement required to reach full speed in this direction
*Joystick Left Throw Sets the amount of joystick movement required to reach full speed in this direction
*Joystick Right Throw Sets the amount of joystick movement required to reach full speed in this direction
*Joystick Deadband Sets the joystick deadband (size of neutral position)
*Invert Left Right JS Axis Sets if the joystick Left/Right axis is inverted
*Invert Fwd Rev JS Axis Sets if the joystick Fwd/Rev axis is inverted
*Swap Joystick Axis Swaps the joystick’s Fwd/Rev and Left/Right axes
Profiled
*Change Mode while Driving Sets if it is possible to change between Modes whilst driving
*Sleep Timer Sets the period of inactivity before the Control System powers down
*Standby Time Sets the period of inactivity before Standby Mode is entered.
*Switch to Standby Sets if an external input switch can be used to enter Standby Mode
*Mode Selection in Standby Sets if the joystick can be used to select Modes when in Standby Mode
Standby in Modes Sets the Modes that Standby will operate in
Standby Forward Sets which Mode is entered with a forward command
Standby Reverse Sets which Mode is entered with a reverse command
Standby Left Sets which Mode is entered with a left command
Standby Right Sets which Mode is entered with a right command
*Remote Selection Sets whether Profiles and Mode can be selected and entered with joystick deflections
*Background Sets the default background for each profile
Speed Paddles
Speed Paddle Operation Sets whether speed adjustment is via a momentary or continuous operation of the CJSM2’s Speed Paddle
Speed Step Size Sets by how much the speed setting will change when the CJSM2’s Speed Paddle is operated
Speed Step Rate Sets the rate at which speed setting changes occur when the Speed Paddle is deflected
Speed Wrap Time Sets a time delay between the speed setting wrapping from maximum to minimum.
Speed Wrap Delay Sets a time delay after a wrap before the speed setting increases from the minimum level
Speed Wrap Beep Sets whether there is an audible beep when the CJSM2’s speed setting wraps from maximum to minimum
Latched
*Latched Drive Selects latched drive operation
*Latched Actuators Selects latched actuator operation
*Latched Timeout Sets the timeout period for latched operation
*Latched Timeout Bleep Sets whether a bleep occurs as the timeout period approaches
Seating
Seating module Enabled Sets which Module is active – SM or ISM
ISM8/CxSM
Global
Actuator Endstop Beep For parameter information - Refer to the Chapter – ISM8
Actuator Mode Entry Axis For parameter information - Refer to the Chapter – ISM8
Axis Setup
Axis Channels For parameter information - Refer to the Chapter – ISM8