Crown Boiler Phantom-X PHNTM210 Скачать руководство пользователя страница 84

Страница: 84 / 120

X. Operation

F. Changing Adjustable Parameters (continued)

“Press”

Modulation

Setup

button to access the following parameters:

Factory

Setting

Range / Choices

Parameter and Description

100%

Minimum to

Maximum

Heat Rate

Central Heat Maximum Expected Heat Rate

This parameter defines the highest modulation rate the Control will go to during a central heat

call for heat. If the rated input of the installed home radiation is less than the maximum output of

the boiler, change the Central Heat Maximum Expected Heat Rate (fan speed) setting to limit the

boiler output accordingly.

80%

Minimum to

Maximum

Heat Rate

Domestic Hot Water (DHW) Maximum Expected Heat Rate

This parameter defines the highest modulation rate the Control will go to during a Domestic Hot

Water call for heat. If the rated input of the indirect water heater is less than the maximum output

of the boiler, change the DHW Maximum Expected Heat Rate (fan speed) setting to limit the boiler

output accordingly.

100%

Minimum to

Maximum

Heat Rate

Auxiliary Maximum Expected Heat Rate

This parameter defines the highest modulation rate the Control will go to during the auxiliary heat

call for heat. If the rated input of the Auxiliary Heat Zones is less than the maximum output of the

boiler, change the Auxiliary Heat Maximum Expected Heat Rate (fan speed) setting to limit the

boiler output accordingly.

40%

Minimum to

Maximum

Heat Rate

Zone 1 Expected Heat Rate (typical for zone 1 through 16)

This parameter defines the highest modulation rate the Control will go to during the Zone 1 call for

heat. If the rated input of the installed home radiation in zone 1 is less than the maximum output

of the boiler, change the Zone 1 Expected Heat Rate (fan speed) setting to limit the boiler output

accordingly.

Minutes

0 to 60 Minutes

Zone Release Time

After the Zone Release Time minutes and a zone has not been satisfied (thermostat opens) the

measured heat loss will be released to increase to the Central Heat Maximum Heat Rate.

See Table

Minimum

- 100 to Maxi

mum

Minimum Heat Rate

This parameter is the lowest modulation rate the Control will go to during any call for heat.

See Table

See Table 29

Lightoff Heat Rate

This is the blower speed during ignition and flame stabilization periods.

Содержание Phantom-X PHNTM210

























































































































Результаты поиска

Содержание Phantom-X PHNTM210

Отзывы:

Похожие инструкции для Phantom-X PHNTM210

Бренды по названию

Популярные бренды

Crown Boiler Phantom-X PHNTM210, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Phantom-X PHNTM210

Отзывы:

Похожие инструкции для Phantom-X PHNTM210

Бренды по названию

Популярные бренды