Crown Boiler Phantom-X PHNTM210 Скачать руководство пользователя страница 93

Страница: 93 / 120

X. Operation

F. Changing Adjustable Parameters (continued)

“Press”

button to access the following parameters:

Factory

Setting

Range / Choices

Parameter and Description

Enabled

Enable Disable

Auxiliary Heat Outdoor Reset Enable

If an outdoor sensor is installed and Outdoor Reset is Enabled, the boiler will automatically

adjust the heating zone set point temperature based on the outdoor reset curve in Figure

45. The maximum set point is defined by the Central Heat Setpoint [factory set to 180°F

(82.2°C)] when the outdoor temperature is 0°F (-18°C) or below. The minimum set point

temperature shown is 130°F (54.4°C) [adjustable as low as 80°F (26.7°C)] when the

outdoor temperature is 50°F (10°C) or above. As the outdoor temperature falls the supply

water target temperature increases. For example, if the outdoor air temperature is 30°F,

(-1.1°C) the set point temperature for the supply water is 150°F (65.6°C).
Disable

Do Not

Calculate setpoint based on outdoor temperature

Enable

Calculate the temperature setpoint based on outdoor temperature using a reset

curve defined by Low Outdoor Temp, High Outdoor Temp, Low Boiler Water

Temp, Min Boiler Temp and Central Heat Setpoint and Boost Time parameters.

0°F

(-18°C)

-40°F to 100°F

(-40°C to 37.8°C)

Auxiliary Heat Low Outdoor Temperature

The Low Outdoor Temperature parameter is also called “Outdoor Design Temperature”.

This parameter is the outdoor temperature used in the heat loss calculation. It is typically

set to the coldest outdoor temperature.

70°F

(21.1°C)

32°F to 100°F

(0°C to 37.8°C)

Auxiliary Heat High Outdoor Temperature

The High Outdoor Temperature parameter is the outdoor temperature at which the Low

Boiler Water Temperature is supplied. This parameter is typically set to the desired building

temperature.

110°F

(43.3°C)

70°F to 190°F

(21.1°C to 87.8°C)

Auxiliary Heat Low Boiler Water Temperature

The Low Boiler Water Temperature parameter is the operating setpoint when the High

Outdoor Temperature is measured. If the home feels cool during warm outdoor conditions,

the Low Boiler Water Temperature parameter should be increased.

0 Minutes

0-1800 Seconds

(0-30 Minutes)

Auxiliary Heat Boost Time

When the Central Heat Setpoint is decreased by Outdoor Reset settings, the Boost Time

parameter is used to increase the operating setpoint when the home heat demand is not

satisfied after the Boost Time setting is exceeded. When heat demand has been “on”

continuously for longer than the Boost Time parameter the operating setpoint is increased

by 10°F (5.6°C). The highest operating setpoint from Boost Time is current Central Heat

Setpoint minus the Central Heat “Diff Above” setting. A setting of 0 seconds disables this

feature.

Содержание Phantom-X PHNTM210

























































































































Результаты поиска

Содержание Phantom-X PHNTM210

Отзывы:

Похожие инструкции для Phantom-X PHNTM210

Бренды по названию

Популярные бренды

Crown Boiler Phantom-X PHNTM210, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Phantom-X PHNTM210

Отзывы:

Похожие инструкции для Phantom-X PHNTM210

Бренды по названию

Популярные бренды