Crown Boiler Phantom-X PHNTM210 Скачать руководство пользователя страница 61

Страница: 61 / 120

VIII. Electrical

(continued)

d. Multiple Boiler Setup

Step

Description

Comments

Install and wire the Header

Sensor

Wire the header sensor to low voltage terminal strip terminals “Header sensor”.

NOTE

This step can not be skipped. The Sequence Master can not be “enabled”unless a Header

Sensor is installed.

Install Ethernet Cables

between boilers

Standard Ethernet type cables with RJ45 connectors are “plugged in” to the Boiler-to-Boiler

Communication Network connection located on the side of the boiler. When more than two

boilers are connected an RJ45 splitter may be used to connect the boilers. Refer to Figure

31.

Apply Power to All Boilers

Set Unique Boiler

Addresses

Assign all boilers a

unique

Boiler Address using any number from 1 through 8.

WARNING

When two boiler’s addresses are the same undesirable simultaneous operation occurs.

Enable 1 Boiler Master

Enable

only one

Control’s Sequencer Master.

WARNING

When more than one Sequencer Master is enable erratic behavior will result.

Power Down All Boilers

Power Up Master

Sequencer

“Enabled” Boiler First

Power Up Other Boilers

Confirm Communication

From the Home Screen of the Control with the Master Sequencer “enabled”, select the Status

button. The Sequencer display shows the boiler address of the communicating boilers.

Additionally, from the “Home” screen select the “Detail” button and then the “Networked

Boilers” buttons to view boiler communication status.
If a boiler is not shown, check Ethernet cable connections and confirm all boilers have unique

addresses.

Содержание Phantom-X PHNTM210

























































































































Результаты поиска

Содержание Phantom-X PHNTM210

Отзывы:

Похожие инструкции для Phantom-X PHNTM210

Бренды по названию

Популярные бренды

Crown Boiler Phantom-X PHNTM210, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Phantom-X PHNTM210

Отзывы:

Похожие инструкции для Phantom-X PHNTM210

Бренды по названию

Популярные бренды