Crown Boiler Phantom-X PHNTM210 Скачать руководство пользователя страница 83

Страница: 83 / 120

X. Operation

F. Changing Adjustable Parameters (continued)

Figure 43: Four Zone House (with Zone Control Connected)

Figure 44: Expected Heat Rate Adjustment (with Zone Control Connected)

Maximum Heat Rate:

Automatically adjusted

by the Control based on

the size and number of

zones calling for heat.

Example “call for heat”

durations for a four zone

house.

Maximum heat rate limits

firing rate and prevents

the Control from firing to

100% in response to a

smaller zone demands.

The Control is shipped with defaults that will provide improved operation. Adjustment is only required to optimize

setup.

The expected heat rate adjustment is used to better match boiler output to the home heating needs. After receiving

a "call for heat" the Control first uses the expected heat rate value to set a maximum heat rate. The maximum heat

rate is the highest heat rate that the boiler can fire to at that moment. The maximum heat rate is the summation of

the expected heat rates for the active (turned on) zones. After establishing the maximum heat rate the Control then

measures water temperature and fires the boiler only as hard as required for the heat demand.

Actual Heat Rate:

Boiler is free to modu-

late based on tempera

ture from minimum to

maximum heat rate.

Expected Heat Rate Adjustment Screens (HeatMatch Software)

NOTE

This feature requires Zone

Control to be connected.

Refer to Electrical section for

Zone Control connection infor-

mation.

The sum of Zone Expected

Heat Rates plus DHW Maxi

mum Expected Heat Rate

(if DHW is active) is used to

calculate the active maximum

modulation rate.

Maximum modulation num

bers are shown in both RPM

and kbtu/hr to allow for easier

understanding of boiler heat

rate.

Содержание Phantom-X PHNTM210

























































































































Результаты поиска

Содержание Phantom-X PHNTM210

Отзывы:

Похожие инструкции для Phantom-X PHNTM210

Бренды по названию

Популярные бренды

Crown Boiler Phantom-X PHNTM210, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Phantom-X PHNTM210

Отзывы:

Похожие инструкции для Phantom-X PHNTM210

Бренды по названию

Популярные бренды