Crown Boiler Phantom-X PHNTM210 Скачать руководство пользователя страница 31

Страница: 31 / 120

a. Both models are listed for vertical venting by

installing flexible stainless steel vent (M&G/

DuraVent FlexNSeal brand) in an UNUSED

masonry chimney/chase and supplying

combustion air through a separate wall or roof

combustion air terminal. The unused chimney

flue must be structurally sound and in good

repair.

b. Refer to Figure 17 for details of chimney chase

installation.

WARNING

Asphyxiation Hazard. Flexible stainless steel

pipe (liner) must be installed at vertical or near

vertical plane when used for combustion product

venting. Failure to do so will result in improper

condensate drainage towards the boiler and

possible subsequent vent pipe blockage.

c. 105290-01 (3”), 102219-01 (3”), and 102220-01

(4”) adapters are available from Crown.

d. FSA-HB3 (3”) and FSA-HB4 (4”) adapters as

well as FasNSeal rigid and flexible vent pipe

are field supplied and available from M&G/

DuraVent.

e. When flexible stainless steel pipe (liner) is used

for combustion product venting, it must be

installed at vertical or near vertical plane. This

will insure proper condensate flow back towards

the boiler.

f. Follow flexible stainless steel pipe (liner)

manufacturer M&G/DuraVent FlexNSeal

specific installation instructions (DuraVent

publication L1150 - latest edition) regarding

application/listing, permits, minimum clearances

to combustibles, installation details (proper joint

assembly, pipe support and routing, gasket and

fitting installation, optional tooling availability/

usage, routing through masonry combination of

combustion product venting and combustion air

supply).

g. When there is a conflict between flexible stainless

steel pipe (liner) manufacturer installation

instructions and Phantom boiler Installation,

Operating and Service Instructions, the more

restrictive instructions shall govern.

E. Removing the Existing Boiler

When an existing boiler is removed from a common

venting system, the common venting system is likely

to be too large for proper venting of the remaining

appliances. At the time of removal of an existing

boiler, the following steps shall be followed with each

appliance remaining connected to the common venting

system placed in operation, while the other appliances

remaining connected to the common venting system are

not in operation.
1. Seal any unused openings in the common venting

system.

2. Visually inspect the venting system for proper

size and horizontal pitch and determine there is no

blockage or restriction, leakage, corrosion, and other

deficiencies which could cause an unsafe condition.

3. Insofar as is practical, close all building doors and

windows and all doors between the space in which

the appliances remaining connected to the common

venting system are located and other spaces of the

building. Turn on clothes dryers and any appliance

not connected to the common venting system.

Turn on any exhaust fans, such as range-hoods and

bathroom exhausts, so they will operate at maxi mum

speed. Do not operate a summer exhaust fan. Close

fireplace dampers.

4. Place in operation the appliance being inspected.

Follow the Lighting (or Operating) Instructions.

Adjust thermo stat so appliance will operate

continuously.

5. Test for spillage at the draft hood relief opening after

5 minutes of main burner operation. Use the flame

of a match or candle, or smoke from a cigarette,

cigar or pipe.

6. After it has been determined that each appliance

remain ing connected to the common venting system

properly vents when tested as outlined above, return

doors, win dows, exhaust fans, fireplace dampers and

any other gas burning appliance to their previous

conditions of use.

7. Any improper operation of the common venting

system should be corrected so the installation

conforms with the

National Fuel Gas Code

, ANSI

Z223.1/NFPA 54 and/or the

Natural Gas and

Propane Installation Code

, CAN/CSA B149.1.

When resizing any portion of the common venting

system, the common venting system should be

resized to approach the minimum size as determined

using the appropriate tables in Part II in the

National

Fuel Gas Code

, ANSI Z223.1/NFPA 54 and/or the

Natural Gas and Propane Installation Code

, CAN/

CSA B149.1.

Au moment du retrait d’une chaudière existante, les

mesures suivantes doivent être prises pour chaque

appareil toujours raccordé au système d’evacuation

commun et qui fonctionne alors que d’autres appareils

toujours raccordés au système d’évacuation ne

fonctionnent pas:
1. Sceller toutes les ouvertures non utilisées du

système d’évacuation.

IV. Venting

D. Stainless Steel Venting, E.. Removing the Existing Boiler (continued)

Содержание Phantom-X PHNTM210

























































































































Результаты поиска

Содержание Phantom-X PHNTM210

Отзывы:

Похожие инструкции для Phantom-X PHNTM210

Бренды по названию

Популярные бренды

Crown Boiler Phantom-X PHNTM210, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Phantom-X PHNTM210

Отзывы:

Похожие инструкции для Phantom-X PHNTM210

Бренды по названию

Популярные бренды