Conductix-Wampfler 0813 Series Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 108

background image

Operating Instructions

Insulated Conductor Rail System

SinglePowerLine Program 0813

BAL0813-0007-EN
www.conductix.com

translated document

page 39 of 108

WARNING!

Risk of injury due to cutting and amputation!

Cuts and amputations can occur:

◼

On the packaging material (e.g.: cartons, bands, etc.).

◼

On sharp edges of the conductor rail.

→

Wear personal protective equipment!

WARNING!

Risk of injury due to puncture wounds and cuts!

The packaging material can contain sharp objects such as nails and wood splinters that can
cause injury to limbs.

→

Wear personal protective equipment!

NOTE!

Damage due to improper transport!

Improper transport can result in substantial property damage.

→

When unloading packaged parts upon delivery and during internal transport, proceed
with caution and observe the symbols and information on the packaging.

→

Only use the attachment points provided.

→

Only remove packaging shortly before installation.

5.2

Transport

Immediately upon receipt, check the delivery for completeness and transport damage.
In case of visible damage, proceed as follows:

◼

Do not accept delivery or accept it only with reservations.

◼

Note the scope of damage on the transport documents, or on the transporter's delivery note.

◼

Initiate a complaint with photos of the damage, if possible.

NOTE!

File a complaint on each defect as soon as it is detected. Damage compensation claims
may only be made within the applicable claim periods.

5.3

Packaging

The individual packages are packed appropriately for the expected transportation conditions.
The packaging has the function of protecting the individual components against damage, corrosion, etc. until they are finally installed.
Hence, do not destroy the packaging; remove it only shortly before installation.

Handling packaging materials:

Dispose of packaging material according to applicable legal regulations and local guidelines.

«
...
37
38
39
40
41
...
»

Содержание 0813 Series













































































































Отзывы:

Нет отзывов

Похожие инструкции для 0813 Series

Бренд: Wayne-Dalton Страницы: 24

Бренд: 2N Страницы: 4

Бренд: Jasic Страницы: 18

TECHNOMIG 210 DUAL SYNERGIC

Бренд: Telwin Страницы: 176

Бренд: Keithley Страницы: 3

Kontron 3.5"-eIO-GPA

Бренд: S&T Страницы: 37

i-Kiosk 100 Plus

Бренд: FingerTec Страницы: 3

ENERGY BOX - TO 1.400

Бренд: AirTechnic Страницы: 20

Hy-Brid Lifts HB-830CE

Бренд: Custom Equipment Страницы: 29

Бренд: Miller Weldmaster Страницы: 20

Q2 IO-MB/DI-16LV

Бренд: ascon Страницы: 3

Бренд: Lincar Страницы: 64

Бренд: Pneumatic Division Страницы: 2

Бренд: Würth Страницы: 256

Бренд: ims PRO Страницы: 78

Бренд: morse Страницы: 8

Бренд: Century Tool Страницы: 76

Бренд: Bosch Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды