Conductix-Wampfler 0813 Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 108

background image

Operating Instructions

Insulated Conductor Rail System

SinglePowerLine Program 0813

BAL0813-0007-EN
www.conductix.com

translated document

page 18 of 108

3

Technical Data

System

Insulated conductor rail system for use in supplying energy to crane systems, the
construction of larger slip ring arrangements, transfer carriages, cable tracks or similar
moving consumers mounted in non-publicly accessible areas, out of hands' reach in
indoor areas and weather-protected outdoor areas (IP2x).

Installation orientation

Current collector insertion from below; current collector insertion from the side is also
possible in indoor areas.

Rail length

5000 mm (nominal size at 20° C/tolerance ± 3 mm)

Phase offset

80 mm (standard)/70 mm (reduced with offset current collector arrangement)

Suspension interval

2.5 m/typically 2.4 to 2.5 m

Maximum system length

Unlimited

Travel speed

Maximum 600 m/min (straight line without interruption)

Permitted ambient temperature

*

-15°C to +55°C (85°C in heat-resistant version/PPE + SB) [Lower temperatures on
request. At lower temperatures, flexible lines should be used.]

Maximum temperature difference

∆ K 40° C

Maximum conductor temperature

+85°C (115°C for heat-resistant version/PPE + SB, briefly 125°C)

Protection type

With current collector insertion from below: IP23 (DIN EN 60529, VDE 0470-1); with
current collector insertion from the side: IP21

Storage temperature

-30°C to +40°C (store in a dry place dry, avoid condensation)

Minimum installation temperature

-10°C (recommended installation temperature: Above 0°C)

Local approvals

UL/CSA/EAC

Max. Air humidity at +40° C

85% rel. H/non-condensing

Altitude above sea level

≤ 2000 m

Travel direction

Forward and backward (reversing)

* Note: At temperatures below -10°C, the mechanical load must be limited through physically limiting the breaking strength.

Conductor bar material

Aluminum with stainless

steel sliding surface

CopperECO

Copper

Type

081313 081314 081319 08131C 08131D 08131I 081315 081316 081317

Current load [A] at 100% DC
and 35°C (rated value)
at 60% DC

500
510

800
810

1000
1050

500
510

800
810

1000
1050

500
520

800
880

1250
1400

Rated voltage

[V]

690 (UL 600 V) - min. 24 V/1 A (minimum load)

Ohmic resistance at

+35°C [Ω/1000 m]

+ 20°C [Ω/1000 m]

0.097
0.092

0.074
0.071

0.051
0.049

0.097

0.092

0.074

0.071

0.051

0.049

0.104
0.097

0.057
0.054

0.033
0.031

Impedance at +20°C [Ω/1000 m]

Impedance at +20°C [Ω/1000 m]

0.157
0.152

0.144
0.140

0.137
0.134

0.157

0.152

0.144

0.140

0.137

0.134

0.161
0.156

0.136
0.134

0.127
0.126

«
...
16
17
18
19
20
...
»

Содержание 0813 Series













































































































Отзывы:

Нет отзывов

Похожие инструкции для 0813 Series

Бренд: RTRMAX Страницы: 14

Бренд: hotset Страницы: 2

Бренд: Nibe Страницы: 16

Бренд: ZiLOG Страницы: 241

Бренд: IDEAL Страницы: 23

Бренд: National Instruments Страницы: 21

Бренд: Blue Giant Страницы: 24

Бренд: FY-TECH Страницы: 34

Бренд: Chamberlain Страницы: 28

PRO POWER VIAS200

Бренд: VITO Страницы: 16

Бренд: stertil-KONI Страницы: 101

Бренд: AA4C Страницы: 30

FieldPoint cFP-AI-100

Бренд: National Instruments Страницы: 17

Бренд: Hong Kong Easyweld Limited Страницы: 18

Бренд: SWS Страницы: 28

Бренд: Siemens Страницы: 65

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды