Compatico AO1 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 25

Compatico AO1 Скачать руководство пользователя страница 24

AO1 / AO2 / AO

2

PolyPanel

ls

24

Flipper Door Installation

1. If a flipper door cover is to be installed, first

install the shelf unit but do not tighten the
screws to the shelf end panel.

2. Loosen top mounting screws on both end

panels to reveal approximately 1/8” of
screw thread.

3. With the flipper door assembly in the

‘open’ position (shown), position the rear
slots of the flipper door assembly over
the rear screws of the shelf end panel.

4. Slide the flipper door assembly back until the

front slots drop over the front screws.

5. Seat flipper door assembly firmly over the four

top shelf end panel screws then securely
tighten all four flipper cover screws then all
four shelf pan screws.

Tack Board & Marker Board Installation

1. Position and engage the hanger clips in panel

joint or on wall hanger strip

(hanger clips are

universal)

at desired height. See table below

right for typical locations.

2. Position board with the mounting screws just

above the hanger clips in the slots of the
hanger clips as shown at right.

3. Press board against hanger clips and down to

engage the mounting screws securely into the
hanger clip notches.

Marker Board Maintenance Notes:

•

Use only dry erasable markers; never use permanent
markers!

•

If permanent marker is accidentally used, remove marks by
writing over the marked area with dry erasable marker and
immediately wiping it clean.

•

Board can be wiped clean with a standard felt eraser. Use
specifically-designed white board cleaner to aid cleaning and
to minimize marker residue.

•

If necessary, clean marker board with lacquer thinner to eliminate any
residue left on the board from permanent markers or other non-approved
writing instruments.

•

Note: Lacquer thinner is extremely flammable and harmful,
or fatal, if swallowed. Vapor is harmful and is an eye and
skin irritant. Avoid contact with skin or eyes; do not use near
a heat source—fire or personal injury may result.

•

Never use an abrasive cleanser on this surface which will cause the
surface to deteriorate rapidly and deliver poor performance.

Flipper Door
Assembly

Threaded hole
and screw

B

Hanger Clip

A

Dimension

A

Tack Board

Height

Dimension

B

Mounting

Screw

Dimensions

(from top)

Dimension

from floor to top

of hanger clip

(approximate)

11

”

1”,

8”

40”

15

”

4”,

11”

41”

«
...
22
23
24
25
»

Содержание AO1


























Отзывы:

Нет отзывов