Compatico AO1 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 25

Compatico AO1 Скачать руководство пользователя страница 21

AO1 / AO2 / AO

2

PolyPanel

ls

21

Screw

End of adjoining,

mounted work surface

Glide

Peninsula
Work Surface

Use two screws

in each bracket

Peninsula Work Surface Installation

Work Surface-supported Installation:

1. Lay work surface, underside up, on a

clean, padded surface.

2. Center support leg, whether single or

dual-leg, set back from end

the

depth (radius) of the surface. Secure
with screws.

3. Mount two work surface connecting

plates to the adjoining, mounted work
surface as shown below.

4. Place peninsula work surface over the

connecting plates and secure with
screws.

5. Adjust glides to level peninsula work

surface.

Peninsula Work Surface Installation

Panel-supported Installation:

1. Engage top tooth of work surface

support bracket (brackets are

handed

)

into slotted channel of panel frame or wall hanger strip, as shown
at right. Then rotate bottom of bracket
down into position of slotted channel.
Typical height for installation is
approximately 28” from floor to the top
of the support bracket.

2. With the panel clips firmly seated,

lower the peninsula work surface onto
the brackets as shown, below right.

3. Drive two screws into each bracket

until tight.

Peninsula Work
Surface, top down

Screw

Work surface connedtor
plate—Mount first to
adjoining mounted work
surface so that they support
the peninsula work surface
when inverted after
installing support leg

Screw

Peninsula support

leg, single or dual-leg

“Tip” bracket into slotted
channel of panel or wall
hanger strip in the same
manner as cantilever

support arm

Work Surface
Support Bracket,
HMP455.02

Right Hand

bracket

shown

«
...
19
20
21
22
23
...
»

Содержание AO1


























Отзывы:

Нет отзывов