Compatico AO1 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 25

Compatico AO1 Скачать руководство пользователя страница 20

AO1 / AO2 / AO

2

PolyPanel

ls

20

Corner Work Surface Installation--

continued

6. Position the corner work surface over support hardware as shown below. Engage the retainer or

“button” and “pin” screws of one side into the cantilever support arm as shown below, right. On
the other side, eliminate the “button” screw, using the “pin” screw to locate it on the support arm.

7. Lower corner work surface fully into position and be sure it is securely seated on all three

support brackets.

Note: early AO

1/AO2

-style retainers are used with cast-aluminum cantilever support arms; button/pin screws are

used

with pressed steel cantilevers.

8. Attach the work surface to the rear corner bracket with two screws; tighten screws securely.
9. Use work surface connecting plates to join corner work surface to adjoining work surfaces.
10. Adjust hex screw at front of cantilever to level work surface, front-to-back.

Panel

Corner Work
Surface

Cantilever

Support Arm

Retainer

(original AO1 “skate”-style

shown)

. Replaced by “button” and

“pin” screws for use with steel
cantilever support arms.

Cantilever
Support Arm

«
...
18
19
20
21
22
...
»

Содержание AO1


























Отзывы:

Нет отзывов