Compatico AO1 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 25

Compatico AO1 Скачать руководство пользователя страница 15

AO1 / AO2 / AO

2

PolyPanel

ls

15

To install Duplex Receptacles

Slide and snap duplex receptacles into each Power Distribution
block where indicated according to electrical plan. Knock out
appropriate duplex covers on each base cover.
To remove duplex receptacle, press release tab on power block and
slide duplex receptacle out.

Power Entry

1. Insert end into power distribution harness block and slide

into position until you hear an audible ‘click’; thread free
end through panel base side cover and install base side
cover.

2. Rotate conduit to the right or left and add Power Entry

cover, Secure with two screws provided.

Power Entry is

now ready for electrician to hardwire the connection to the
building supply.

•

End Feed and Ceiling Feed cables connect to
power distribution block male terminals on end of
block.

WARNING

•

Risk of Fire or Electrical Shock. Each panel must be connected to only one source of electrical
supply. Be sure to turn off panel board switch while installing or removing power entry.

•

Power Entry must be installed by a licensed electrician.

Wiring Guide

Gray
White
Green/Yellow
Green
Pink
Blue
Red
Black

Neutral 2
Neutral 1
Isolated Ground
Ground
Hot Circuit 4
Hot Circuit 3
Hot Circuit 2
Hot Circuit 1

«
...
13
14
15
16
17
...
»

Содержание AO1


























Отзывы:

Нет отзывов