Compatico AO1 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 25

Compatico AO1 Скачать руководство пользователя страница 16

AO1 / AO2 / AO

2

PolyPanel

ls

16

Base & Connector Raceway Management

Opening Panel Base Side Covers:

Side covers are retained by the top channel and pivot at the baseplate.

1. To remove side cover, start at one end and press down on the top

edge of the side cover to clear the lip from the top channel; pull
toward you as your finger continues pressing down on the top edge
as it slides along toward the other end.

2. Rotate side cover down toward you to allow access to the cable

management channel.

Closing Panel Base Side covers:

Note: Connector trim covers must be closed before closing side covers.

1. Start at one end of the side cover

and press down on the top edge
until the lip is under the top
channel.

2. While holding that end in position,

press and run finger along the top
edge seating the rest of the lip
under the top channel.

Connector Trim Covers:

•

Trim covers are completely
installed on all post connectors, except 4-way connectors which have a base post but no trim cover.

•

Trim covers pivot at the base and hold their position with a latch that engages the connector.

•

To release the trim cover, press down and in with a flat blade screw driver, near the center at top. When the
trim cover latch clears the edge of the connector, rotate the trim cover back.

Top Channel

Side Cover

Baseplate / Hinge

Adjustable Glide

Panel

Side Cover

Lip

Hinge

Rotate

Support

Post

Support
Post

Connector

Connector

Connector

Support
Post

Trim

Covers

Trim

Cover

Trim

Cover

2-Way 90

˚

Connector

2-Way 180

˚

Connector

3-Way Connector

Trim

Cover

Latches

Support
Post

Connector

2-Way 90

˚

Connector--

Closed

«
...
14
15
16
17
18
...
»

Содержание AO1


























Отзывы:

Нет отзывов