Compatico AO1 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 25

Compatico AO1 Скачать руководство пользователя страница 13

AO1 / AO2 / AO

2

PolyPanel

ls

13

“T” Connection Installation

Use to connect a panel at a right angle to a structural wall or to another, non-steel frame, panel of
the same height.

Notice: It is the installer’s responsibility to select and install
the proper fasteners in the structural wall or panel frame.
Compatico does not assume liability for their use.

For attachment to all panels, except tubular steel frame:

1. Position the T-Connector channel at the desired

location, flush with top of panel and parallel to its
vertical edges, with notch up for clearance of panels
top cap.

2. Use holes in channel for template, bore 3/16”

diameter hole 1

” deep into panel frame; two at the

top, two at the bottom.

3. Securely fasten wedge blocks and channel to panel

surface with #14 X 1

” long Sheet Metal Screws.

4. Remove paper cover from adhesive strip on back of

filler strip and position filler in channel, between
wedge blocks, and press firmly in place.

5. Assemble panel to T-Connector with a standard

panel connector.

For attachment to structural wall:

Note: Structural wall should be constructed in either of the following manners, as a minimum:

•

Composite Board (drywall) over Wood or Metal Stud: Drywall must be 5/8” minimum, on 2” x 4” studs
minimum, 24”on-center maximum; 14’ height maximum, retained at both floor and ceiling. Metal studs
must be “C”-channel, 20-ga minimum thickness. Drywall must be attached by industry standards,
minimum; ideally it should include appropriate adhesive bead on each stud, the full length of the stud.

•

Poured cement wall

•

Cement block wall

1. Select a wood furring strip, straight

and sound, with minimum cross
section dimensions of 1

” X 2”. The

length must match the nominal height
of the T-Connection.

2. Bevel or plane the back of the furring

strip so that face of furring strip will be
plumb.

3. Select appropriate fastener for type of

structural wall and mount the furring
strip to the structural wall,
perpendicular and resting on the floor.

4. Locate

channel

vertically,

with

notch

at bottom.

5. Follow steps 2 – 5 above to attach T-

Connector to furring strip.

Top Cap

Notch

Filler Strip

#14 X 1

”

long

Sheet Metal Screws

Top (small)
Wedge Block

Flush

Channel

Furring Strip

Structural

Wall

1

”

Minimum

Notch

«
...
11
12
13
14
15
...
»

Содержание AO1


























Отзывы:

Нет отзывов