manualshive.com logo in svg

Compatico AO1, Инструкция по эксплуатации, Страница: 2 / 25

Поделиться
Скачать
Compatico AO1 Скачать руководство пользователя страница 2

AO1 / AO2 / AO

2

 PolyPanel

ls

 

2

Table of Contents 

Introduction ...............................................................................................................2 

Tools Required ..................................................................................................3 
Electrical Power Distribution & Wire Management .........................................4 
Pre-Installation Requirements ..........................................................................4 
Installation Preparation .....................................................................................4 
Installation Sequence........................................................................................5 
Panel Support ....................................................................................................5 
Load Capacities.................................................................................................6 

Panel Installation ......................................................................................................7 
Connecting Panels to Connectors ..........................................................................7 
Connecting Panels to Panels ..................................................................................8 
Panel End Cap Kit ....................................................................................................8 
Panel Height Change—At Connector .....................................................................9 
Panel Height Change—In-line.................................................................................10 
Variable Height Filler Trim .......................................................................................11 
Wall Hanger Strips ...................................................................................................11 
T-Connection Installation .........................................................................................13 
Power Distribution 

Specifications & Installation ................................................................................................... 14 
Duplex Receptacles................................................................................................................. 15 
Power Entry ............................................................................................................................... 15 
Wiring Guide.............................................................................................................................. 15 
Panel Base & Connector Base Covers.............................................................................. 16 
Base End Caps......................................................................................................................... 17

Work Surfaces 

Straight.........................................................................................................................18 
Corner ..........................................................................................................................19 
Peninsula ..................................................................................................................................21 
Transaction Surface ..............................................................................................................22 
Pencil Drawer..........................................................................................................................22

Overhead Storage 

Shelf ...........................................................................................................................................23 
Flipper Door .............................................................................................................................24 
Tack Board/Marker Board...................................................................................................24 
Task Light.................................................................................................................................25 

Storage Pedestals..........................................................................................................................25 

Содержание AO1


























Отзывы:

Нет отзывов