manualshive.com logo in svg

Compatico AO1, Инструкция по эксплуатации, Страница: 23 / 25

Поделиться
Скачать
Compatico AO1 Скачать руководство пользователя страница 23

AO1 / AO2 / AO

2

 PolyPanel

ls

 

23 

Shelf Installation

 

Note:  All screws must be firmly tightened. Failure to do so may cause the 

shelf to fall, causing product  damage or personal injury

. 

1. Loosen both bottom shelf mounting screws on each end panel to

reveal approximately 1/8” of screw thread. Bottom screws are for
the shelf; top screws are for the flipper door assembly or additional
shelf, if specified.

2. Engage shelf end panel at desired height in slotted hanger frame

of panel or wall track channel as show at right, top.

3. Swing shelf end panel to perpendicular with panel or wall and lock

shelf end panel in place by pushing down on end panel to seat the
bracket. Tap firmly with plastic mallet to ensure end panel is fully
seated on hanger frame or wall hanger strip.

4. Position end panels perpendicular to wall and slide shelf straight in

between shelf end panels, just above the mounting screws. Seat
shelf pan securely on the mounting screws and tighten with a
Philips screw driver; be certain to tighten all screws firmly.

Shelf Divider 

1. Install shelf divider by tilting divider forward and

hook under lip of shelf as shown.

2. Pivot divider so that it rests flat on the shelf.

Shelf 

Divider 

Side view 

Wall Track 
or Panel

Shelf 
End

End Panel 

Shelf Pan 

End Panel 

Shelf Pan 

7

”

h

 Shelf 

15

”

h

 Shelf 

Содержание AO1


























Отзывы:

Нет отзывов