Comelit KSW3207LU Скачать руководство пользователя страница 38

Страница: 38 / 56

Edit outputs

This menu is used to edit the settings for the output, after an output has already been set. For example: if, while using the control

panel, the installer needs to edit a configuration for an existing sounder, this menu can be used to select the sounder and move

through its configuration. The output can also be deleted.
• Select output

This menu entry is used to select the output to be edited.

◊ Edit description

See RF sounder programming

◊ Edit type

See RF sounder programming

◊ Edit attributes

See RF sounder programming

◊ Delete output

This menu entry is used to delete an output from the control panel memory.

Dev. settings

◊ Global output settings

- External sounder

◊ Single device settings

- Select output

◊ Default management

- Select output

- Default for all outputs

N.B. to inhibit the audible signalling devices, the control panel needs to be switched to maintenance mode as follows:

Installer code (001961 if default), then the down arrow.

Command URL

This menu is used to edit and/or enter a URL command, that is an HTTP string generated by third parties and copied in the

corresponding “Sounder & Output” menu sheet in the Hub Manager configuration SW. In this software section, a link to the “Supla”

◊ Description

Used to edit the description of a command.

◊ URL

Used to enter the desired URL command.

Wired outputs

The system has two wired outputs which can be configured from this menu. Refer to the RF outputs for attribute types and

definitions.

Select output

•  Description
•  Type
•  Attributes

Video devices

This menu is used to configure the IP cameras on the control panel.

N.B. up to 16 IP cameras can be connected in live mode. Of these, a maximum of 4 will be able to record simultaneously

upon an alarm event or continuously 24 hours a day.

New CCTV device

• IP address

This menu is used to enter the IP address of the IP camera to be added.

• Port

This menu is used to enter the IP port of the IP camera to be added.

• Description

Содержание KSW3207LU

























































Результаты поиска

Содержание KSW3207LU

Отзывы:

Бренды по названию

Популярные бренды

Comelit KSW3207LU, Техническое руководство

Результаты поиска

Содержание KSW3207LU

Отзывы:

Бренды по названию

Популярные бренды