ClearSpan 105115 Скачать руководство пользователя | Manualshive

Страница: 5 / 37

background image

The following graphics and photos identify the different
parts and show how they are used. (Not all parts are
shown.)

105099 Dome Arena Crown

Purlin Connection Brackets (105350) used to attach
purlins to the rafters. Diagram also shows the bolt
hardware.

105098 Pipe Connector (from 104302 assembly)

NOTE:

The 104302 assembly (see insert above)

includes a base plate.

Base plate is not used for this

arena.

The bolt, lock washer, and nut are used to attach

the pipe fitting to the ground posts.

Ratchet attached to ground post

10015808 Two-Socket Cross for Sidewall

10015108 Single-Socket Tee for Sidewall

Pictorial Parts Guide

Not all parts are shown.

Purlin Connection
Bracket for Purlins

Purlin

Visit www.ClearSpan.com for additional products and customer assistance.

4 of 36

«
...
3
4
5
6
7
...
»

Содержание 105115






































Отзывы:

Нет отзывов

Похожие инструкции для 105115

Бренд: PAPILLON Страницы: 2

Бренд: SunnCamp Страницы: 3

COOLABAH AWNING

Бренд: Aussie Traveller Страницы: 3

Бренд: Grand Canyon Страницы: 4

Бренд: Strongway Страницы: 12

CAMPO CASA XT 5P

Бренд: Vaude Страницы: 59

Бренд: Mammoth Страницы: 2

Бренд: ROBINHOOD Страницы: 4

Бренд: Thermarest Страницы: 2

Бренд: Jack Wolfskin Страницы: 12

LAGUNA CABANA LOUNGER 2006539

Бренд: Backyard Discovery Страницы: 44

AIRBEAM AirAway Sapera Standard

Бренд: Vango Страницы: 2

Party Tent AIR 4x4

Бренд: Kampa Страницы: 9

Бренд: Palram Страницы: 25

Бренд: Vaude Страницы: 46

Бренд: Creative Страницы: 17

Бренд: Dancover Страницы: 16

Бренд: Harbor Freight Tools Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды