ClearSpan 105115 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 37

background image

INSTALL THE COVER CONDUIT

The cover conduit is inserted into a pocket that runs
around the cover in the cover skirt. See the dashed line
in the photo below. The conduit lengths are connected
using 1.66" cover conduit couplers (see arrows).

INSTALLING A SECTION OF CONDUIT ABOVE THE
GATE OPENING IS OPTIONAL AND DEPENDS ON
WHAT THE SHELTER IS USED FOR.

See dashed line

in the diagram below. These instructions do not install
this section of the cover conduit.

Complete the following steps:

1. Using one 190P0795 plain pipe (79 ½") and one

190S099 swaged pipe (99") for each conduit,
assemble all cover conduits.

2. Secure each joint with two Tek screws and tape over

the joint and screws using the supplied duct tape.

3.

BEGINNING AT EITHER SIDE OF THE GATE

, feed

one cover conduit into the cover pocket.

ATTENTION:

Additional help is needed when feeding

the conduit into each pocket.

4. Once all cover conduits are in place, insert a cover

coupler (60DA166C) to connect the conduit
sections. See the following diagram.

Cover has been removed to show the components.

5. With all couplers installed (see above), verify that the

conduit and coupler assembly is centered in the
cover pocket and secure each coupler to each
conduit using two Tek screws. See diagram above.

6. Measure the length needed to reach from the lower

QH1065 ratchet to the coupler and back to the lower
ratchet and cut a section of 2" yellow strap from the
bulk roll. DO NOT CUT THE STRAP TOO LONG.
DOING SO MAY RESULT IN TOO MUCH WASTE.

7. Take the strap, wrap it around the conduit coupler,

and thread both ends into the QH1065 ratchet.

8. Slightly tighten the strap and repeat the steps to cut

and install the remaining 2" straps. Work your way
around the shelter and evenly tighten the straps.

NOTE:

Recheck all straps and tighten if needed. The

yellow strap will stretch over the upper ratchet.

9. After the main cover is stretched and secured, install

the side panels (optional). (To purchase optional
side panels, contact Customer Service at 1-800-245-
9881.)

Installing a
conduit above
the gate is
optional.

Feed each conduit
into each pocket.

Cover
Conduit

Coupler

Cover
Conduit

Install two
Tek screws

Install two
Tek screws

Install conduit couplers at each ground post.

Visit www.ClearSpan.com for additional products and customer assistance.

23 of 36

«
...
22
23
24
25
26
...
»

Содержание 105115






































Отзывы:

Нет отзывов

Похожие инструкции для 105115

Бренд: GentleTent Страницы: 5

Бренд: Boutique Camping Страницы: 8

TRIMLINE CANOPY 10' x 10'

Бренд: Flourish Страницы: 10

Бренд: Warner Shelter Systems Limited Страницы: 16

ELLOWSTONE VENT II

Бренд: Jack Wolfskin Страницы: 16

STITCHLINE 4-POLE SUN SHADE 2000001652

Бренд: Coleman Страницы: 2

Бренд: TENTCO Страницы: 2

Бренд: Yarden Страницы: 20

Бренд: MSR Страницы: 1

Бренд: ClearSpan Страницы: 29

Бренд: Ozark Trail Страницы: 2

Бренд: Ozark Trail Страницы: 1

KUBOTA RTV-XG850

Бренд: Kubota Страницы: 99

BUNGALOW GARAGE

Бренд: Nemo Страницы: 8

Бренд: RioOutdoors Страницы: 27

Бренд: Dancover Страницы: 6

Бренд: Dancover Страницы: 17

Standard Awning

Бренд: EasyAwn Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды