ClearSpan 105115 Скачать руководство пользователя | Manualshive

Страница: 22 / 37

background image

tied, but remain loose so the cover can be moved
and aligned as needed.

Verify that cover remains aligned with the rafters so the
straps can be properly attached to the ratchets.

8. Continue pulling the cover into position and using

the straps to temporarily secure it to the rafters.

9. Once the entire cover is in place, work the cover

around the frame to properly align it on the frame
and to align the center hole with the crown at the top
of the frame.

INSTALL MID AND UPPER RATCHETS

1. Locate the black straps on the inside/underside of

the cover. The straps serve as guides for the
installation of the ratchets.

2. Using Tek screws, attach a ratchet

as close to the

underside of the rafter pipe

as possible.

NOTE:

Verify that the ratchet

does not

touch the cover

and that the cable does not hamper its operation.

Cover straps are
pulled through the
crown opening and
are secured to each
ratchet.

Attach
QH1061
Ratchet

Visit www.ClearSpan.com for additional products and customer assistance.

21 of 36

«
...
20
21
22
23
24
...
»

Содержание 105115






































Отзывы:

Нет отзывов

Похожие инструкции для 105115

Бренд: Yoli Страницы: 2

Бренд: Ohenry Productions Страницы: 7

Бренд: Ohenry Productions Страницы: 7

Бренд: Exped Страницы: 2

Бренд: GigaTent Страницы: 2

MG LAKEWOOD LODGE

Бренд: Magellan Outdoors Страницы: 9

Бренд: Costway Страницы: 6

AERO TXL PRO Series

Бренд: Zempire Страницы: 2

Бренд: Zempire Страницы: 2

Бренд: Grand Canyon Страницы: 4

Бренд: Grand Canyon Страницы: 5

Бренд: Costco Страницы: 33

Бренд: Vaude Страницы: 58

Бренд: Vaude Страницы: 67

Бренд: Zempire Страницы: 2

Бренд: Mammoth Tents Страницы: 2

Бренд: LUDI Страницы: 2

Бренд: RioOutdoors Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды