ClearSpan 105115 Скачать руководство пользователя | Manualshive

Страница: 25 / 37

background image

INSTALL OPTIONAL SIDE PANELS

Side panels are attached to the sidewall frame and
ground posts and help to shield the interior from weather
and wind. Side panels can be installed to decrease
distractions, or removed to increase ventilation and light.

ATTENTION:

Skip this procedure if you are not installing

side panels at this time.

Parts required for the side panel installation.

•

Side Panels

•

Tie-Downs

Complete the following steps to install the side panels.

Photo shows side panels on a similar shelter.

1. Unfold a side panel and position it between two

ground posts.

2. Insert the end of the tie-down through the grommet

of the side panel.

Diagram shows a snugger ball tie down.

3. Wrap the tie-down cord around the ground post or

frame tube and thread the ball of the tie-down
through the double cord of the tie-down to secure it
in place. See previous diagram.

Photo may show a shelter that differs in design.

Photo is used to show the position of the tie-downs and
the side panels. Shelter shown may differ from your
shelter.

4. Repeat the steps to install the remaining tie-downs

for the panel.

5. Repeat the procedure to install the remaining side

panels.

6. Read

the

High Crown Arena Care and

Maintenance

information.

Visit www.ClearSpan.com for additional products and customer assistance.

24 of 36

«
...
23
24
25
26
27
...
»

Содержание 105115






































Отзывы:

Нет отзывов

Похожие инструкции для 105115

Бренд: skandika outdoor Страницы: 2

Бренд: NETTUNO Marine Equipment Страницы: 2

EVENT BUDGET TENT

Бренд: Vispronet Страницы: 2

EVENT TENT COMPACT

Бренд: Vispronet Страницы: 2

Бренд: ClearSpan Страницы: 13

Бренд: ClearSpan Страницы: 23

Бренд: Sojag Страницы: 30

Бренд: Aqua Products Страницы: 8

GEMSBOK BOW TENT 3 X 3 M

Бренд: Bushtec Adventure Страницы: 2

BUNGALOW GARAGE

Бренд: Nemo Страницы: 8

Residence AIR All-Season Size 13-18

Бренд: Dometic Страницы: 68

Бренд: Dancover Страницы: 20

Бренд: Garden Treasures Страницы: 4

Casa Africa SAVANNA LODGE CARBET

Бренд: PartySpace Страницы: 28

Eskimo QUICKFISH Series

Бренд: Ardisam Страницы: 2

Prospector & Miner Framed Wall Tent

Бренд: Alaska Tent & Tarp Страницы: 2

Бренд: Clas Ohlson Страницы: 16

Бренд: EuroTrail Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды