Cisco SF500-24 Скачать руководство пользователя страница 289 | Manualshive

Страница: 289 / 477

background image

Configuring IP Information

Management and IP Interfaces

Cisco 500 Series Stackable Managed Switch Administration Guide

280

17

IPv6 nodes require an intermediary mapping mechanism to communicate with
other IPv6 nodes over an IPv4-only network. This mechanism, called a tunnel,
enables IPv6-only hosts to reach IPv4 services, and enables isolated IPv6 hosts
and networks to reach an IPv6 node over the IPv4 infrastructure.

Tunneling uses the ISATAP mechanism. This protocol treats the IPv4 network as a
virtual IPv6 local link, with mappings from each IPv4 address to a link local IPv6
address.

The switch detects IPv6 frames by the IPv6 Ethertype.

Defining IPv6 Global Configuration

The

IPv6 Global Configuration

page defines the frequency of the IPv6 ICMP error

messages generated by the switch.

To define IPv6 global parameters:

STEP 1

In Layer 2 mode, click

Administration

>

Management Interface

>

IPv6 Global

Configuration

.

In Layer 3 mode, click

IP Configuration

>

Management and IP Interfaces

>

IPv6

Global Configuration

.

The

IPv6 Global Configuration

page opens.

STEP 2

Enter values for the following fields:

•

ICMPv6 Rate Limit Interval

—Enter how often the ICMP error messages are

generated.

•

ICMPv6 Rate Limit Bucket Size

—Enter the maximum number of ICMP error

messages that can be sent by the switch per interval.

STEP 3

Click

Apply

. The IPv6 global parameters are written to the Running Configuration

file.

Defining an IPv6 Interface

An IPv6 interface can be configured on a port, a LAG, VLAN, or ISATAP tunnel
interface. The switch supports one IPv6 interface as an IPv6 end device.

A tunnel interface is configured with an IPv6 address based on the settings
defined in the

IPv6 Tunnel

page.

«
...
287
288
289
290
291
...
»

Содержание SF500-24






























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SF500-24

Бренд: D-Link Страницы: 267

Бренд: H3C Страницы: 1089

Бренд: FELA Страницы: 13

Бренд: Enttec Страницы: 22

DigiTOOLS VS-41USB

Бренд: Kramer Страницы: 8

TK-205K - PS/2 KVM Switch

Бренд: TRENDnet Страницы: 11

Бренд: Maiwe Страницы: 5

Бренд: axing Страницы: 4

Бренд: Intermatic Страницы: 1

Бренд: SMC Networks Страницы: 1

Бренд: MicroNet Страницы: 74

Бренд: Comm-Tec Страницы: 40

Бренд: Grizzly Страницы: 2

Бренд: Yacoub Automation GmbH Страницы: 45

Бренд: GoMax Electronics Страницы: 6

LAN MASTER 33022.B

Бренд: Transition Networks Страницы: 12

Бренд: 3onedata Страницы: 2

Бренд: CAI Networks Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды