Cisco ONS 15454 M6 Скачать руководство пользователя страница 36

Страница: 36 / 164

DLP-G563 Mounting the Air Deflectors (Front-to-Front) on the ONS 15454 M6
Shelf for ETSI Rack Configuration

This task installs the air deflectors (front-to-front) on the ONS 15454 M6 shelf
for ETSI rack configuration.

The air deflectors can be installed only in the front position of the
chassis.

Note

Purpose

• #2 Phillips Dynamometric screwdriver
• Medium slot-head screwdriver
• Small slot-head screwdriver

Tools/Equipment

NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454
M6 Shelves

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Use only the fastening hardware provided with the ONS 15454 M6 to prevent loosening, deterioration, and
electromechanical corrosion of the hardware and joined material.

Caution

Procedure

Step 1

Place the right front air deflector flush against the right side of the chassis (see the following figure).

Step 2

Align the screw holes on the right front air deflector with the screw holes on the right side of the chassis.

Figure 34: Mounting the Air Deflectors (Front-to-Front) on the ONS 15454 M6 Shelf for ETSI Rack Configuration

Step 3

Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).

Step 4

Place the left front air deflector flush against the left side of the chassis.

Do not mount the left front deflector (exhaust air deflector), if these cards are to be installed in the ONS 15454
M6 shelf:

Installing the ONS 15454 M6 Shelf

DLP-G563 Mounting the Air Deflectors (Front-to-Front) on the ONS 15454 M6 Shelf for ETSI Rack Configuration

Содержание ONS 15454 M6





































































































































































Результаты поиска

Содержание ONS 15454 M6

Отзывы:

Похожие инструкции для ONS 15454 M6

Бренды по названию

Популярные бренды

Cisco ONS 15454 M6, Руководство по установке

Результаты поиска

Содержание ONS 15454 M6

Отзывы:

Похожие инструкции для ONS 15454 M6

Бренды по названию

Популярные бренды