Cisco ONS 15454 M6 Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 164

background image

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

The MSM (multishelf management) ports are present on the ECU module. The MSM ports located on the left
side of the ECU module correspond to the TNC/TNCE/TSC/TSCE card in Slot 1, and the MSM ports located
on the right side correspond to the TNC/TNCE/TSC/TSCE card in Slot 8. For more information about the
ECU module and MSM ports, see the

External Connection Units, on page 72

Note

This procedure explains the steps to connect the ONS 15454 multishelf node and subtending shelves to a
24-port Catalyst 2950 or Catalyst 3560 switch. Follow the steps provided in this procedure to connect the
multishelf node to the 48-port Catalyst 2950 or Catalyst 3560 switch.

Note

Cisco ONS 15454 M12 subtended shelf does not support connecting to NCS multi-shelf node.

Note

Procedure

Step 1

Using a cross-over (CAT-5) LAN cable:

a) Plug one connector into Port 1 of the active Catalyst 3560.
b) Plug the other connector into the front panel of the node controller TCC2/TCC2P/TCC3 card in Slot 7.

Step 2

Using a cross-over (CAT-5) LAN cable:

a) Plug one connector into Port 1 of the standby Catalyst 3560.
b) Plug the other connector into the front panel of the node controller TCC2/TCC2P/TCC3 card in Slot 11.

Step 3

Using a cross-over (CAT-5) LAN cable:

a) Plug one connector into Port 23 of the active Catalyst 3560.
b) Plug the other connector into Port 23 of the standby Catalyst 3560.

Use TCC3 cards in the ONS 15454 node controller while connecting it to the ONS 15454 M6
subtending shelves and when there are more than 12 subtending shelves.

Note

Step 4

To connect an ONS 15454 M6 subtending shelf to the Catalyst 3560 switches, complete the following:

a) Using a cross-over (CAT-5) LAN cable:

•

• Plug one connector into the MSM port of the subtending ONS 15454 M6 shelf that corresponds

to the TNC/TNCE/TSC/TSCE card in Slot 1.

• Plug the other connector into Port 2 of the active Catalyst 3560.

b) Using a cross-over (CAT-5) LAN cable:

Installing the ONS 15454 M6 Shelf

146

Installing the ONS 15454 M6 Shelf

DLP-G683 Connect the ONS 15454 as the Node Controller in a Mixed Multishelf Configuration

«
...
144
145
146
147
148
...
»

Содержание ONS 15454 M6





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454 M6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды