Cisco ONS 15454 M6 Скачать руководство пользователя страница 144

Страница: 144 / 164

• Plug the other end into the MSM port of the node controller ONS 15454 M6 shelf that

corresponds to the TNC/TNCE/TSC/TSCE card in Slot 1.

b) Using a cross-over (CAT-5) LAN cable:

•

• Plug one connector into the MSM port of the subtending ONS 15454 M6 shelf that corresponds

to the TNC/TNCE/TSC/TSCE card in Slot 8.

• Plug the other end into the MSM port of the node controller ONS 15454 M6 shelf that

corresponds to the TNC/TNCE/TSC/TSCE card in Slot 1.

c) Repeat Step 1a and Step 1b to connect the remaining MSM ports on the node controller ONS 15454 M6

shelf to the MSM ports on the subtending ONS 15454 M6 shelf.

Step 2

To connect an ONS 15454 subtending shelf to the ONS 15454 M6 node controller, complete the following:

a) Using a cross-over (CAT-5) LAN cable:

•

• Plug one connector into the front panel of the subtending shelf TCC2/TCC2P/TCC3 card in

Slot 7.

• Plug the other end into the MSM port of the node controller ONS 15454 M6 shelf that

corresponds to the TNC/TNCE/TSC/TSCE card in Slot 1.

b) Using a cross-over (CAT-5) LAN cable:

•

• Plug one connector into the front panel of the subtending shelf TCC2/TCC2P/TCC3 card in

Slot 11.

• Plug the other end into the MSM port of the node controller ONS 15454 M6 shelf that

corresponds to the TNC/TNCE/TSC/TSCE card in Slot 8.

c) Repeat Step 2a and 2b for each subtending shelf in the multishelf configuration using the remaining MSM

ports on the node controller ONS 15454 M6 shelf.

Step 3

To connect an ONS 15454 subtending shelf to the ONS 15454 M6 subtending shelf, complete the following:

a) Using a cross-over (CAT-5) LAN cable:

•

• Plug one connector into the front panel of the subtending shelf TCC2/TCC2P/TCC3 card in

Slot 7.

• Plug the other end into the MSM port of the subtended ONS 15454 M6 shelf that corresponds

to the TNC/TNCE/TSC/TSCE card in Slot 1.

b) Using a cross-over (CAT-5) LAN cable:

•

• Plug one connector into the front panel of the subtending shelf TCC2/TCC2P/TCC3 card in

Slot 11.

• Plug the other end into the MSM port of the subtended ONS 15454 M6 shelf that corresponds

to the TNC/TNCE/TSC/TSCE card in Slot 8.

c) Repeat Step 3a and 3b for each subtending shelf in the multishelf configuration using the remaining MSM

ports on the subtending ONS 15454 M6 shelf.

Installing the ONS 15454 M6 Shelf

144

Installing the ONS 15454 M6 Shelf

DLP-G729 Connect the ONS 15454 M6 as the Node Controller in a Mixed Multishelf Configuration without a Catalyst Switch

Содержание ONS 15454 M6





































































































































































Результаты поиска

Содержание ONS 15454 M6

Отзывы:

Похожие инструкции для ONS 15454 M6

Бренды по названию

Популярные бренды

Cisco ONS 15454 M6, Руководство по установке

Результаты поиска

Содержание ONS 15454 M6

Отзывы:

Похожие инструкции для ONS 15454 M6

Бренды по названию

Популярные бренды