Cisco Nexus 3400 Series Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 72

background image

Step 5

Insert the rack-mount retainer brackets

a) Align the retainer brackets to the front of the chassis, being careful not to damage anything on the front of the chassis

(see the following figure).

b) Repeat Step 5 to attach the other retainer bracket on other side of the chassis.

c) Tighten the 10-32 screws to 20 in-lb (2.26 N·m) or tighten the 12-24 screws to 30 in-lb (3.39 N·m).

Step 6

Insert the retainer clip to hold the chassis in place.

a) Align the retainer clip to the inside of the back of the slider rail. Make sure to hook the flange to the cutout on the

bracket and align the screw holes (see the following figure).

b) Attach the screws to secure the retainer clip (see the following figure).
c) Repeat Step 6 to attach the other retainer clip on the other side of the chassis.

Cisco Nexus 3400 Hardware Installation Guide

25

Installing the Chassis

Installing the Switch using the NXK-ACC-RMK-2RU Rack-mount Kit

«
...
31
32
33
34
35
...
»

Содержание Nexus 3400 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 3400 Series

Бренд: Painless Performance Products Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: HPM Страницы: 4

Бренд: BERNSTEIN Страницы: 3

Бренд: SMART Страницы: 46

Бренд: FCI Страницы: 12

SwitchMan USB-Combo SW2

Бренд: Raritan Страницы: 2

TEG-S50TXE SHEETS

Бренд: TRENDnet Страницы: 20

ProSAFE JGS516PE

Бренд: NETGEAR Страницы: 2

Бренд: DirectConnect Страницы: 10

Бренд: Phonocar Страницы: 2

Бренд: Radio Systems Страницы: 19

Бренд: 3onedata Страницы: 2

pro-trim PT1000

Бренд: Seastar Solutions Страницы: 2

Бренд: Kramer Страницы: 2

Бренд: A-Neuvideo Страницы: 16

Бренд: Veris Industries Страницы: 2

Бренд: I-Tech Страницы: 123

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды