Cisco Nexus 3400 Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 72

background image

Installing the Switch Using the N3K-C3064-ACC-KIT Rack-Mount Kit

To install the switch, you must attach front and rear mounting brackets to the switch, install slider rails on the
rear of the rack, slide the switch onto the slider rails, and secure the switch to the front of the rack. Typically,
the front of the rack is the side easiest to access for maintenance.

You must supply the eight 10-32 or 12-24 screws required to mount the slider rails and switch to the rack.

Note

Before you begin

• You have inspected the switch shipment to ensure that you have everything ordered.

• Make sure that the switch rack-mount kit includes the following parts:

• Front rack-mount brackets (2)

• Rear rack-mount brackets (2)

• Slider rails (2)

• M4 x 0.7 x 8-mm Phillips countersink screws (12)

• The rack is installed and secured to its location.

Step 1

Install two front-mount brackets to the switch as follows:

a) Determine which end of the chassis is to be located in the cold aisle as follows:

• If the switch has port-side intake modules (fan modules with burgundy coloring), position the switch so that its

ports will be in the cold aisle.

• If the switch has port-side exhaust modules (fan modules with blue coloring), position the switch so that its fan

and power supply modules will be in the cold aisle.

b) Position a front-mount bracket so that four of its screw holes are aligned to the screw holes on the side of the chassis.

You can align any four of the holes in the front rack-mount bracket to four of the six screw holes on the
side of the chassis (see the two ways to mount these brackets on a typical chassis, in following figure). The
holes that you use depend on the requirements of your rack and the amount of clearance required for interface
cables (3 inches [7.6 mm] minimum) and module handles (1 inch [2.5 mm] minimum).

Note

Cisco Nexus 3400 Hardware Installation Guide

15

Installing the Chassis

Installing the Switch Using the N3K-C3064-ACC-KIT Rack-Mount Kit

«
...
21
22
23
24
25
...
»

Содержание Nexus 3400 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 3400 Series

Бренд: 3Com Страницы: 8

Бренд: Eaton Страницы: 8

Бренд: Intermatic Страницы: 1

Бренд: KCC Страницы: 6

Бренд: Icy Box Страницы: 6

Бренд: ASTEK Страницы: 3

Nexoos 370 Series

Бренд: Soyntec Страницы: 7

Бренд: Accton Technology Страницы: 547

Бренд: Gefen Страницы: 56

Бренд: LevelOne Страницы: 35

Бренд: S+S Страницы: 16

8 PORT SMART SWITCH CE 232D4SS8

Бренд: B&B Electronics Страницы: 29

Smart view IC-1304-IO

Бренд: C&C TECHNIC Страницы: 2

Бренд: AV-Box Страницы: 11

Бренд: PTN Страницы: 44

Бренд: Emos Страницы: 44

Бренд: Black Box Страницы: 4

Total Access 1210

Бренд: ADTRAN Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды