Cisco Nexus 3400 Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 72

background image

• The installation site meets the following requirements as stated in Chapter 2:

• Environmental requirements for temperature, humidity, altitude, and air particulates.

• Cabinet or rack is installed and meets the requirements for the switch.

Jumper power cords are available for use in a cabinet.

Note

• The rack is positioned so that you can install the switch with its cold air intakes positioned in a cold

aisle.

If the fan and power supply modules are burgundy or red colored, you must install the chassis with
its port side in a cold aisle. If the modules are blue colored, you must be able install the chassis with
the fan modules in a cold aisle.

• Earth ground connection is close to the switch. You must be able to easily connect the switch directly

to an earth ground or indirectly through a grounded rack.

High leakage current. Earth connection essential before connecting to power
supply.

Warning

• Site power meets the switch requirements. If you are using n+n redundancy, you must have two

power sources within reach of the switch when it is installed in the cabinet or rack.

If available, you can use an uninterruptible power supply (UPS) to protect against power failures.

Avoid UPS types that use ferroresonant technology. These UPS types can become
unstable with systems such as the Cisco Nexus 3000 Series switches. These
switches can have substantial current draw fluctuations because of fluctuating
data traffic patterns.

Caution

Ensure that circuits are sized according to local and national codes. For North America, the power
supply requires a 15-A or 20-A circuit.

To prevent loss of input power, ensure the total maximum loads on the circuits
supplying power to the switch are within the current ratings for the wiring and
breakers.

Caution

Cisco Nexus 3400 Hardware Installation Guide

9

Installing the Chassis

Preparing to Install the Chassis

«
...
15
16
17
18
19
...
»

Содержание Nexus 3400 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 3400 Series

Бренд: Maipu Страницы: 21

Бренд: Maico Страницы: 56

Бренд: CoolGear Страницы: 2

Бренд: steute Страницы: 20

Бренд: Black Box Страницы: 4

TM-1-8210 Series

Бренд: Eaton Страницы: 3

Бренд: Fairchild Страницы: 20

Бренд: Hamlet Страницы: 2

Бренд: Davey Страницы: 2

SI1P-SH-DVI-UCAC

Бренд: Black Box Страницы: 16

Бренд: Canoga Perkins Страницы: 7

Бренд: GarrettCom Страницы: 77

Бренд: Ubiquiti Страницы: 14

Бренд: LevelOne Страницы: 15

Бренд: Goobay Страницы: 16

Бренд: Top View Страницы: 13

Бренд: Omron Страницы: 31

Бренд: Linksys Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды