Cisco Nexus 3400 Series Скачать руководство пользователя страница 66

Страница: 66 / 72

Description

Status

LED

Component

The operator has
activated this LED
to identify this
switch in the
chassis.

Flashing blue

Beacon (BCN)

Chassis (front and
back)

Identifies the chassis
receiving the beacon
signal.

On (blue)

Identification (ID)

This port has no
physical link.

Left side

Off

Solid on (green)

Management
(MGMT)

This port has a
physical link.

This port has no
activity.

Right side

Off

Blinking (green)

This port has
activity.

Green and amber
LED used to
indicate
customer-defined
status for each port.

Customer defined states

Port

This port is not in
use.

This port is unusable
during breakout.

Off

All diagnostics pass.
The module is
operational.

Solid on (green)

Status (STS)

The module is not
receiving power.

Off

On (amber)

Cisco Nexus 3400 Hardware Installation Guide

LEDs

Содержание Nexus 3400 Series









































































Результаты поиска

Содержание Nexus 3400 Series

Отзывы:

Похожие инструкции для Nexus 3400 Series

Бренды по названию

Популярные бренды

Cisco Nexus 3400 Series, Руководство по установке оборудования

Результаты поиска

Содержание Nexus 3400 Series

Отзывы:

Похожие инструкции для Nexus 3400 Series

Бренды по названию

Популярные бренды