Cisco Nexus 3400 Series Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 72

background image

About Requirements for Perforated Cabinets

A perforated cabinet has perforations in its front and rear doors and side walls. In addition to the requirements
listed in the “General Requirements for Cabinets and Racks” section, perforated cabinets must meet the
following requirements:

• The front and rear doors must have at least a 60-percent open area perforation pattern, with at least 15

square inches (96.8 square cm) of open area per rack unit of door height.

• The roof should be perforated with at least a 20-percent open area.

• The cabinet floor should be open or perforated to enhance cooling.

The Cisco R Series rack conforms to these requirements.

About Requirements for Open Racks

In addition to the requirements listed in the “General Requirements for Cabinets and Racks” section on page
A-1, if you are mounting the chassis in an open rack (no side panels or doors), ensure that the rack meets the
following requirements:

• The minimum vertical rack space per chassis must be two rack units (RU), equal to 3.47 inches (8.8 cm).

• The horizontal distance between the chassis and any adjacent chassis should be 6 inches (15.2 cm), and

the distance between the chassis air vents and any walls should be 2.5 inches (6.4 cm).

Cisco Nexus 3400 Hardware Installation Guide

52

Rack Specifications

About Requirements for Perforated Cabinets

«
...
58
59
60
61
62
...
»

Содержание Nexus 3400 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 3400 Series

Бренд: D-Link Страницы: 73

Бренд: Gefen Страницы: 11

xStack DES-3500 Series

Бренд: D-Link Страницы: 260

DXS-3600 Series

Бренд: D-Link Страницы: 48

DXS-3400 SERIES

Бренд: D-Link Страницы: 3

Web Smart Switch DGS-1210-16

Бренд: D-Link Страницы: 71

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 56

xStack DES-3800 Series

Бренд: D-Link Страницы: 326

xStack DES-3526

Бренд: D-Link Страницы: 222

Бренд: D-Link Страницы: 2

DXS-1210 Series

Бренд: D-Link Страницы: 20

Бренд: Cisco Страницы: 30

Бренд: 3Com Страницы: 8

PathBuilder S200 Series

Бренд: 3Com Страницы: 11

Бренд: 3Com Страницы: 8

CoreBuilder 3500

Бренд: 3Com Страницы: 96

Бренд: LAUMAS Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды