Cisco Nexus 3400 Series Скачать руководство пользователя страница 68

Страница: 68 / 72

Description

Status

LED

Component

All diagnostics pass. The
module is operational.

Solid on (green)

Status

Fan

The module is not
receiving power.

Off

The module is booting or
running diagnostics.

Solid on (amber)

If the module fails during
an initial reset, the LED
continues to blink and the
module does not come
online.

The module has a runtime
failure and is brought
offline.

Blinking (amber)

Power Supply LEDs

This table provides information about power supply LEDs for Cisco Nexus 3000 Series switches.

Description

Status

LED

Component

Power supply is on and
okay.

Solid on

OK (green)

Power supply

3.3 voltage standby (VSB)
is on but the power supply
unit is not powering the
other modules.

Blinking

No power to the power
supply.

Off

Power supply failure,
overvoltage, overcurrent,
or overheating.

Solid on

FAULT (amber)

Power is present, 3.3 VSB
on, and the power supply
is off.

PSU fan rotor is not
functioning normally.

Blinking

Operating normally.

Off

Cisco Nexus 3400 Hardware Installation Guide

LEDs

Power Supply LEDs

Содержание Nexus 3400 Series









































































Результаты поиска

Содержание Nexus 3400 Series

Отзывы:

Похожие инструкции для Nexus 3400 Series

Бренды по названию

Популярные бренды

Cisco Nexus 3400 Series, Руководство по установке оборудования

Результаты поиска

Содержание Nexus 3400 Series

Отзывы:

Похожие инструкции для Nexus 3400 Series

Бренды по названию

Популярные бренды