Cisco Nexus 3400 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 72

background image

Statement 1017—

Restricted Area

This unit is intended for installation in restricted access areas. A restricted access area can be accessed by
skilled, instructed or qualified personnel.

Warning

Statement 1030—

Equipment Installation

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning

Installation Options with Rack-Mount Kits, Racks, and Cabinets

The rack-mount kit enables you to install the switch into racks of varying depths. You can position the switch
with easy access to either the port connections or the fan and power supply modules.

You can install the switch using the following 1 (RU) rack-mount options:

• Rack-mount kit (NXK-ACC-KIT-1RU) which you can order from Cisco. This option offers you easy

installation, greater stability, increased weight capacity, added accessibility, and improved removability
with front and rear removal.

• Rack-mount kit (N3K-C3064-ACC-KIT) which you can order from Cisco.

You can install the switch using the following 2 (RU) rack-mount options:

• Rack-mount kit (NXK-ACC-RMK-2RU) which you can order from Cisco. This option offers you easy

installation, greater stability, increased weight capacity, added accessibility, and improved removability
with front and rear removal.

• Rack-mount kit (N9K-C9300-RMK) which you can order from Cisco.

You can install the switch in the following types of racks:

• Open EIA rack

• Perforated EIA cabinet

The rack or cabinet that you use must meet the requirements listed the in

General Requirements and Guidelines

for Cabinets and Racks, on page 51

section.

You are responsible for verifying that your rack and rack-mount hardware comply with the guidelines that
are described in this doc.

Note

Preparing to Install the Chassis

Before you can install the switch, you must verify the following:

Cisco Nexus 3400 Hardware Installation Guide

8

Installing the Chassis

Installation Options with Rack-Mount Kits, Racks, and Cabinets

«
...
14
15
16
17
18
...
»

Содержание Nexus 3400 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 3400 Series

Бренд: S&C Страницы: 26

Бренд: S&C Страницы: 37

Бренд: S&C Страницы: 28

DES-3224 - Switch

Бренд: D-Link Страницы: 75

xStack DGS-3427

Бренд: D-Link Страницы: 246

Бренд: Jasco Страницы: 2

Бренд: Aastra Страницы: 52

Бренд: DANLERS Страницы: 2

Бренд: Festo Страницы: 2

Бренд: Z-Band Страницы: 13

StorageWorks SAN Switch Integrated/32

Бренд: Compaq Страницы: 104

Crocodile Tail Loop

Бренд: One Control Страницы: 9

CEFLA PIR DALIP

Бренд: DANLERS Страницы: 2

Бренд: SMC Networks Страницы: 2

Бренд: H3C Страницы: 27

SM24-1000SFP-AH

Бренд: Transition Networks Страницы: 76

BOCAHUB-16 Plus BEN220

Бренд: Boca Страницы: 56

Бренд: Efapel Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды