Cisco Nexus 3400 Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 72

background image

Step 2

Install the chassis into the rack.

a) Use two M4 screws to attach the brackets to the rack.

M4 screws (2 each side)

2

Front-mounting position

1

Installing a 2 (RU) Chassis in a Four-Post Rack

Before you install the chassis, be sure that the rack is fully secured to the data center floor.

Installing the Switch using the NXK-ACC-RMK-2RU Rack-mount Kit

To install the switch, you must attach mounting brackets to the rack, install slider rails on the rear of the rack,
slide the switch onto the slider rails, install the retainer brackets, and secure the switch to the rack with the
retainer clips. Typically, the front of the rack is the side easiest to access for maintenance.

You must supply the eight 10-32 or 12-24 screws required to mount the slider rails and switch to the rack.

Note

Before you begin

• You have inspected the switch shipment to ensure that you have everything ordered.

• Make sure that the switch rack-mount kit includes the following parts:

• Rack-mount brackets (2)

• Rack-mount retainer brackets (2)

Cisco Nexus 3400 Hardware Installation Guide

22

Installing the Chassis

Installing a 2 (RU) Chassis in a Four-Post Rack

«
...
28
29
30
31
32
...
»

Содержание Nexus 3400 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 3400 Series

IP-Reach IPR-M1

Бренд: Raritan Страницы: 4

Бренд: H3C Страницы: 90

Бренд: vantiva Страницы: 58

Бренд: Aruba Страницы: 6

Бренд: FS Страницы: 33

Бренд: Hamlet Страницы: 4

Бренд: Watchguard Страницы: 26

INTEGRAL Series

Бренд: DAS AUDIO Страницы: 45

Бренд: Lockly Страницы: 12

Бренд: Manhattan Страницы: 4

Бренд: NegoRack Страницы: 41

Бренд: Velleman Страницы: 4

Бренд: Black Box Страницы: 13

Бренд: Gefen Страницы: 12

Бренд: FeinTech Страницы: 22

Бренд: Kramer Страницы: 10

SMART Home AWMR-230

Бренд: Trust Страницы: 57

Бренд: Ascent Communication Technology Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды