Cisco Nexus 3400 Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 72

background image

Statement 1005—

Circuit Breaker

When AC or HVAC power supply is used:

This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective devices is rated not greater than 20A (North
America), 16A (Europe), and 13A (UK).

When HVDC power supply is used:

This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective devices is rated not greater than 10A.

Warning

• There is adequate clearance around the rack to install the switch and to allow for unimpeded airflow.

• You have the following equipment in addition to the switch and the kits shipped with the switch:

• Eight customer-supplied 12-24 or 10-32 screws (required for attaching slider rails and mounting

bracket to the mounting rails)

• Number 1 and number 2 Phillips screwdrivers with torque capability

• 3/16-inch flat-blade screwdriver

• Tape measure and level

• ESD wrist strap or other grounding device (wrist strap can be found in the accessory kit)

• Antistatic surface large enough to place the switch

• Grounding cable (6 AWG recommended), sized according to local and national installation

requirements; the required length depends on the proximity of the switch to proper grounding
facilities

• Crimping tool large enough to accommodate the girth of the grounding lug

• Wire stripping tool

Unpacking and Inspecting the Chassis

When handling switch components, such as fan or power supply modules, wear a grounded ESD strap and
handle the modules by their carrier edges only. To ground the ESD strap, make sure that it is attached to an
earth ground, a grounded chassis, or a grounded rack.

Caution

Keep the shipping container in case the chassis requires shipping in the future.

Tip

Cisco Nexus 3400 Hardware Installation Guide

10

Installing the Chassis

Unpacking and Inspecting the Chassis

«
...
16
17
18
19
20
...
»

Содержание Nexus 3400 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 3400 Series

Бренд: La Toulousaine Страницы: 6

Бренд: VeEX Страницы: 22

Бренд: Moxa Technologies Страницы: 7

Бренд: TRENDnet Страницы: 2

Бренд: ATEN Страницы: 2

Бренд: Pulse-Eight Страницы: 9

Storage Networking SAN128B-6

Бренд: IBM Страницы: 116

Бренд: Unipoe Страницы: 9

Бренд: Cabletron Systems Страницы: 116

SwitchMan USB-Combo SW4

Бренд: Raritan Страницы: 2

Бренд: Blagdon Страницы: 6

Бренд: N-audio Страницы: 8

ConferX AC-CX84-AUHD

Бренд: AVPro Edge Страницы: 6

Бренд: Microsens Страницы: 42

Бренд: QNAP Страницы: 28

Бренд: Plantronics Страницы: 17

Бренд: Datacom Systems Страницы: 55

Бренд: Larson Electronics Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды