Cisco Nexus 3400 Series Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 72

background image

• Front rack-mount brackets (2)

• Rear rack-mount brackets (2)

• Slider rails (2)

• M4 x 0.7 x 8-mm Phillips countersink screws (12)

• The rack is installed and secured to its location.

Step 1

Install two front rack-mount brackets and the two rear rack-mount brackets to the switch as follows:

a) Determine which end of the chassis is to be located in the cold aisle as follows:

• If the switch has port-side intake modules (fan modules with burgundy coloring), position the switch so that its

ports will be in the cold aisle.

• If the switch has port-side exhaust modules (fan modules with blue coloring), position the switch so that its fan

and power supply modules will be in the cold aisle.

b) Position the front rack-mount bracket and the rear rack-mount bracket so that its screw holes are aligned to the screw

holes on the side of the chassis.

You can align the holes in the rack-mount bracket to the holes on the side of the chassis (see the two ways
to mount these brackets on a typical chassis, in following figure). The holes that you use depend on the
requirements of your rack and the amount of clearance required for interface cables (3 inches [7.6 mm]
minimum) and module handles (1 inch [2.5 mm] minimum).

Note

c) Secure the front-mount bracket and the back-mount bracket to the chassis using four M4 screws and tighten each

screw to 12 in-lb (1.36 N·m) of torque.

Cisco Nexus 3400 Hardware Installation Guide

12

Installing the Chassis

Installing the Switch Using the NXK-ACC-KIT-1RU Rack-Mount Kit

«
...
18
19
20
21
22
...
»

Содержание Nexus 3400 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 3400 Series

EasySmart DGS-1100-08

Бренд: D-Link Страницы: 44

Бренд: pathway Страницы: 28

Бренд: GE Страницы: 302

SmartSwitch 9A100

Бренд: Cabletron Systems Страницы: 52

SmartSwitch 9W006

Бренд: Cabletron Systems Страницы: 34

SmartSTACK ELS100-S24TX2M

Бренд: Cabletron Systems Страницы: 102

Бренд: Cabletron Systems Страницы: 24

SmartSwitch 9000

Бренд: Cabletron Systems Страницы: 14

Бренд: Cabletron Systems Страницы: 38

Бренд: Fema Страницы: 96

Бренд: DANLERS Страницы: 2

Бренд: Vector Страницы: 6

Бренд: Zamel Страницы: 2

Бренд: UniFi Страницы: 8

STI Echotel 919

Бренд: Magnetrol Страницы: 12

Бренд: Micrel Страницы: 15

Бренд: NBK Страницы: 32

CheetaHub Power-3004E

Бренд: Accton Technology Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды