Cisco Nexus 3400 Series Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 72

background image

Mounting rails on rack or cabinet posts.

3

Fasten the chassis to the front of the rack with two
12-24 or 10-32 screws on each side.

1

Front-mount bracket.

2

d) Tighten the 10-32 screws to 20 in-lb (2.26 N·m) or tighten the 12-24 screws to 30 in-lb (3.39 N·m).

Step 6

If you attached a grounding wire to the chassis grounding pad, connect the other end of the wire to the facility ground.

Installing a 1 (RU) Chassis in a Two-Post Rack

This section describes the rack installation for the Cisco Nexus 3000 series switch into a two-post rack.

To install a switch, you must attach mounting brackets to the switch and secure the switch to the rack.
Installation in racks other than 19-inch racks requires a bracket kit not included with the switch.

The following figure shows the standard 19-inch mounting brackets.

Cisco Nexus 3400 Hardware Installation Guide

19

Installing the Chassis

Installing a 1 (RU) Chassis in a Two-Post Rack

«
...
25
26
27
28
29
...
»

Содержание Nexus 3400 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 3400 Series

Бренд: E-T-A Страницы: 6

Бренд: G&D Страницы: 36

Бренд: JB Systems Light Страницы: 15

Бренд: VeEX Страницы: 22

Бренд: Ruby Tech Страницы: 301

Бренд: LEGRAND Страницы: 30

Бренд: VADA Страницы: 4

Бренд: Videplus Страницы: 13

Бренд: W Box Technologies Страницы: 10

Бренд: I-Tech Страницы: 19

Бренд: Linkskey Страницы: 2

Бренд: ENSIM SENSORS Страницы: 15

24/48 10/100 Ports + 2GE

Бренд: Accton Technology Страницы: 512

Бренд: H3C Страницы: 31

Бренд: Uniclass Страницы: 33

Бренд: Hirschmann Страницы: 8

Бренд: TRENDnet Страницы: 19

Бренд: Kramer Страницы: 165

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды