Cisco Nexus 3400 Series Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 72

background image

The console port can be used to connect to a modem. If you do not connect it to a modem, connect it either
before powering the switch on or after the switch has completed the boot process.

Caution

Before you begin

Before you connect the switch to a console, ensure that you have the following:

• Computer terminal that supports VT100 terminal emulation. The terminal emulation software (such as

HyperTerminal or Procomm Plus) makes communication between the switch and a computer possible
during setup and configuration.

Step 1

Configure the terminal emulator program to match each of the following default port characteristics:

• 9600 baud

• 8 data bits

• 1 stop bit

• No parity

Step 2

Connect the DB-9 connector on the other end of the cable to the computer serial port.

What to do next

You are ready to configure the switch.

Connecting the Management Interface

Before you begin

To prevent an IP address conflict, you must complete the initial configuration and establish an IP address for
the switch.

Step 1

Connect the appropriate modular cable to on the switch.

Step 2

Connect the other end of the cable to the switch, hub, or router.

Connecting Interface Ports to Other Devices

After you perform the initial configuration for the switch and create a management connection, you are ready
to connect the interface ports on the switch to other devices. Depending on the types of interface ports on the

Cisco Nexus 3400 Hardware Installation Guide

40

Connecting the Switch to the Network

Connecting the Management Interface

«
...
46
47
48
49
50
...
»

Содержание Nexus 3400 Series









































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 3400 Series

D-PFS4226-24ET-240

Бренд: Dahua Страницы: 58

Бренд: jablotron Страницы: 2

SANbox 5000 Series

Бренд: Qlogic Страницы: 8

Бренд: Raritan Страницы: 4

Бренд: StarTech.com Страницы: 2

Бренд: NTI Страницы: 15

Бренд: Metrix Страницы: 12

Бренд: Endress+Hauser Страницы: 25

INTEGRA KLI 310

Бренд: Velux Страницы: 9

Custom Pro Matrix

Бренд: Bluestream Страницы: 27

Бренд: Omron Страницы: 4

Бренд: Cabletron Systems Страницы: 110

Бренд: Cypress Страницы: 16

Бренд: TRENDnet Страницы: 2

Бренд: Popp Страницы: 9

Бренд: Kramer Страницы: 4

Бренд: Santon Страницы: 16

Бренд: 3One data Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды