Cisco FM1000 Gateway Скачать руководство пользователя страница 98

Страница: 98 / 138

•

When the overwrite is complete, make sure that the upgraded
firmware has a greater version number than the firmware that
was previously installed.

• If the firmware version has not changed, the firmware

upgrade has failed. Repeat the overwrite from step

Step 1

above.

6.8.4. Plug-In management

IMPORTANT

For a complete list of software plug-ins that are currently
available for the Cisco FM1000 Gateway, refer to

“Available

plug-ins” (page 109)

The MANAGE PLUG-INS page shows which software plug-ins are
currently active on the unit, and contains controls that allow you to do the
following functions:

• Upload activation codes that allow the unit's accessory software

plug-ins to function.

• Activate uploaded software plug-ins for use with the unit.
• Deactivate uploaded software plug-ins so they can be used on

other Fluidmesh units.

• Activate a non-repeatable Demo mode that allows full 4.9 GHz,

AES and unlimited plug-in functionality for an 8-hour trial period.

• Show and erase the log files for plug-in installation.

To open the

MANAGE PLUG-INS

dialog, do the following steps:

•

Click the

-manage plug-ins

link under

MANAGEMENT

SETTINGS

in the left-hand settings menu.

• The

MANAGE PLUG-INS

dialog will be shown (

Figure 49

(page 99)

Device configuration using the configurator interface

Page 98 of 138

Содержание FM1000 Gateway









































































































































Результаты поиска

Содержание FM1000 Gateway

Отзывы:

Похожие инструкции для FM1000 Gateway

Бренды по названию

Популярные бренды

Cisco FM1000 Gateway, Руководство по установке и настройке

Результаты поиска

Содержание FM1000 Gateway

Отзывы:

Похожие инструкции для FM1000 Gateway

Бренды по названию

Популярные бренды