Cisco FM1000 Gateway Скачать руководство пользователя страница 33

Страница: 33 / 138

Figure 12. Partner Portal (Two Factor Auth. icon)

• The

Two Factor Authentication page

will be shown.

• The current two-factor authentication status of your portal

account will be shown near the top of the page.

Click the

Set Up Two Factor Authentication

button.

• A two-factor authentication dialog will ask to confirm your

identity. If the name and E-mail address shown in the
dialog are yours, enter your current portal password and
click the

Validate identity

button.

An E-mail will be sent to your E-mail address with a verification
code in the body of the mail. Enter the verification code in the

Verification code

field of the Two Factor Authentication web

page.

• The Two Factor Authentication web page will show a QR

code.

Use the authentication app on your mobile phone to scan the QR
code on the web page.

Figure 13 (page 33)

is a typical example

of the QR code you will be shown.

Figure 13. Two Factor Authentication (typical QR code)

• The authenticator app will generate an authentication code.

Enter this code in the

Authentication code

field of

the Two Factor Authentication web page, and click the

Enable Two Factor Authentication

button.

• A list of ten

recovery codes

will be shown on the Two

Factor Authentication web page. It is recommended that
you save these codes in case you lose your mobile phone.
Download the recovery codes as a *.TXT file by clicking

Using the Fluidmesh Partner Portal

Page 33 of 138

Содержание FM1000 Gateway









































































































































Результаты поиска

Содержание FM1000 Gateway

Отзывы:

Похожие инструкции для FM1000 Gateway

Бренды по названию

Популярные бренды

Cisco FM1000 Gateway, Руководство по установке и настройке

Результаты поиска

Содержание FM1000 Gateway

Отзывы:

Похожие инструкции для FM1000 Gateway

Бренды по названию

Популярные бренды