Cisco FM1000 Gateway Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 138

background image

6. Device configuration using the configurator
interface

All Fluidmesh radio transceiver devices are shipped with IP address

192.168.0.10

, and Netmask

255.255.255.0

.

The Cisco FM1000 Gateway can be configured by using:

• The RACER™ Radio Configuration interface, or
• The on-board Configurator interface.

The

Configurator

is a localized configuration software platform that

resides on the Fluidmesh device.

• Local configuration is done by connecting a computer to the device

through a direct hardware connection, or through the internet.

• Using the Configurator, devices can be configured on an

Offline

basis only. A configuration (*.CONF) file can be manually applied to
set the device parameters, or each device parameter can be
manually set by the device user.

• Offline configuration settings for more than one Fluidmesh device

type  can  be  integrated  into  a  single  configuration  file.  When  the
configuration  file  is  uploaded  to  each  device,  the  device
automatically  loads  the  correct  configuration  settings  for  its  device
type.

To configure the unit using the

Configurator

, refer to the following sub-

sections.

Device configuration using the configurator interface

© 2021 Cisco and/or its affiliates. All rights reserved.

Page 36 of 138

«
...
34
35
36
37
38
...
»

Содержание FM1000 Gateway











































































































































Отзывы:

Нет отзывов

Похожие инструкции для FM1000 Gateway

DVG-G1402S - Wireless Broadband VoIP Router

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 2

Бренд: Linkskey Страницы: 8

Бренд: Airlink101 Страницы: 7

Бренд: Inseego Страницы: 68

Бренд: Hama Страницы: 67

Бренд: FMN Страницы: 28

Бренд: TCL Страницы: 23

Бренд: Avaya Страницы: 16

Бренд: IBM Страницы: 44

Бренд: Abocom Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды