Cisco FM1000 Gateway Скачать руководство пользователя страница 54

Страница: 54 / 138

• Plot all stationary wireless devices in a Fluidmesh network, or plot

all stationary devices in a Fluidmesh Fluidity network in relation to
the mobile wireless-equipped vehicles from which they receive
relayed traffic.

• Plot all wireless links within a network.
• Show important information about each static device, mobile device

and wireless link.

• Diagnose problems with wireless links.
• Show user-configured physical positions of all Fluidmesh

components in a wireless network, against the background of an
aerial map.

IMPORTANT

For detailed information on the operational concepts that
govern Fluidity, refer to the

Cisco Ultra-Reliable Wireless

Backhaul Fluidity Specifications

document.

Plotting and interpreting the wireless links

NOTE

The statistical information refresh period is:

• One second for Fluidity (mobile) networks.

• Six seconds for stationary networks.

To plot and interpret all wireless links in the current network, click the

QUADRO™

link in the upper left part of the settings menu (below).

Device configuration using the configurator interface

Page 54 of 138

Содержание FM1000 Gateway









































































































































Результаты поиска

Содержание FM1000 Gateway

Отзывы:

Похожие инструкции для FM1000 Gateway

Бренды по названию

Популярные бренды

Cisco FM1000 Gateway, Руководство по установке и настройке

Результаты поиска

Содержание FM1000 Gateway

Отзывы:

Похожие инструкции для FM1000 Gateway

Бренды по названию

Популярные бренды