manualshive.com logo in svg

Cisco Catalyst 4500 Series, Руководство по настройке программного обеспечения

Серия продуктов Cisco Catalyst 4500 предлагает удобное и надежное решение для сетевой конфигурации. Скачайте бесплатно Руководство по настройке программного обеспечения на manualshive.com и получите подробную информацию о функционале и возможностях данного устройства. Надежность Cisco Catalyst 4500 Series - ваш проводник в мире сетевых технологий.

Поделиться
Скачать
background image

61-4

Catalyst 4500 Series Switch, Cisco IOS Software Configuration Guide - Cisco IOS XE 3.8.0E and IOS 15.2(4)E

 

Chapter 61      DHCPv6 Options Support

Information About DHCPv6 Options Support

To maintain interoperability with existing DHCP relays and servers, LDRA implements the same 
message types (RELAY-FORWARD and RELAY-REPLY) as a DHCPv6 relay agent. LDRA allows 
relay-agent information to be inserted by an access node that performs a link-layer bridging (that is, 
non-routing) function. The LDRA resides on the same IPv6 link as the client and a DHCPv6 relay agent 
or server.

LDRA for VLANs and Interfaces

You can configure LDRA on VLANs and interfaces. LDRA is not enabled by default. You must enable 
it on the VLAN or interface first.

In a typical deployment, a majority of the interfaces or ports on a device are client facing. In such a 
scenario, you can configure LDRA functionality on the VLAN. When you configure LDRA on a VLAN, 
the functionality is configured on all ports or interfaces within the VLAN. Instead of configuring LDRA 
functionality individually on interfaces and ports within a VLAN, you can configure LDRA on the entire 
VLAN. As a result, all ports or interfaces associated with the VLAN will be configured as client facing.

You can also configure LDRA functionality on a specific interface or port. An interface or port can be 
configured as client-facing trusted, client-facing untrusted, or server facing.

The LDRA configuration on a VLAN has to be configured as trusted or untrusted. An LDRA must 
implement a configuration setting for all client-facing interfaces, marking them as trusted or as 
untrusted.

By default, any interface that is configured as client facing will be configured as an untrusted interface. 
When a client-facing interface is deemed untrusted, LDRA will discard any message of type 
RELAY-FORWARD received from the client-facing interface.

CAPWAP Access Controller DHCPv6 Option

The Control And Provisioning of Wireless Access Points (CAPWAP) protocol allows lightweight access 
points to use DHCPv6 to discover a Wireless Controller to which it can connect. CAPWAP is a standard, 
interoperable protocol that enables a controller to manage a collection of wireless access points.

Wireless access points use the DHCPv6 option 52 (RFC 5417) to supply the IPv6 management interface 
addresses of the primary, secondary, and tertiary Wireless Controllers.

Both stateless and stateful DHCPv6 addressing modes are supported. In stateless mode, access points 
obtain IPv6 address using the Stateless Address AutoConfiguration (SLAAC), while additional network 
information (not obtained from router advertisements) is obtained from a DHCPv6 server. In stateful 
mode, access points obtain both IPv6 addressing and additional network information exclusively from 
the DHCPv6 server. In both modes, a DHCPv6 server is required to provide option 52 if Wireless 
Controller discovery using DHCPv6 is required.

Содержание Catalyst 4500 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 4500 Series

D-Link DSL-504T Manual preview
DSL-504T
Бренд: D-Link Страницы: 99
D-Link DI-804V Datasheet preview
DI-804V
Бренд: D-Link Страницы: 5
D-Link DES-1210-08P Manual preview
DES-1210-08P
Бренд: D-Link Страницы: 15
D-Link AirPro DWL-6000AP Manual preview
AirPro DWL-6000AP
Бренд: D-Link Страницы: 65
C&H Technologies EM405-8 Manual preview
EM405-8
Бренд: C&H Technologies Страницы: 46
Idis DR-4100P Series Installation Manual preview
DR-4100P Series
Бренд: Idis Страницы: 30
Quantum Scalar 50 Upgrade Instructions preview
Scalar 50
Бренд: Quantum Страницы: 20
H3C S10500 Series Mpls Configuration Manual preview
S10500 Series
Бренд: H3C Страницы: 400
TP-Link Archer MR500 User Manual preview
Archer MR500
Бренд: TP-Link Страницы: 110
8level IPG-200 User Manual preview
IPG-200
Бренд: 8level Страницы: 52
SAB SABVISION NVR32 Quick Start Manual preview
SABVISION NVR32
Бренд: SAB Страницы: 29
B&B Electronics Elinx ESW200 Series Quick Start Manual preview
Elinx ESW200 Series
Бренд: B&B Electronics Страницы: 20
Caton NVE 9100 User Manual preview
NVE 9100
Бренд: Caton Страницы: 18
Ubiquiti EdgeRouter PoE ERPoe-5 Quick Start Manual preview
EdgeRouter PoE ERPoe-5
Бренд: Ubiquiti Страницы: 13
3Com EtherLink 3C905C-TX User Manual preview
EtherLink 3C905C-TX
Бренд: 3Com Страницы: 96
Intercoax IXWB-450 Quick Start Manual preview
IXWB-450
Бренд: Intercoax Страницы: 2
AOpen ISDN SOHO Router User Manual preview
ISDN SOHO Router
Бренд: AOpen Страницы: 89
Tripp Lite N201-003-WH Specifications preview
N201-003-WH
Бренд: Tripp Lite Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды