Cisco Catalyst 3130 Скачать руководство пользователя | Manualshive

Страница: 677 / 1354

background image

C H A P T E R

29-1

Cisco Catalyst Blade Switch 3130 and 3032 for Dell Software Configuration Guide

OL-12247-04

29

Configuring LLDP, LLDP-MED, and Wired
Location Service

This chapter describes how to configure the Link Layer Discovery Protocol (LLDP), LLDP Media
Endpoint Discovery (LLDP-MED) and wired location service on the switch. Unless otherwise noted, the
term

switch

refers to a standalone switch and to a switch stack.

Note

For complete syntax and usage information for the commands used in this chapter, see the command
reference for this release and the “System Management Commands” section in the

Cisco IOS

Configuration Fundamentals Command Reference, Release 12.2

.

•

Understanding LLDP, LLDP-MED, and Wired Location Service, page 29-1

•

Configuring LLDP, LLDP-MED, and Wired Location Service, page 29-4

•

Monitoring and Maintaining LLDP, LLDP-MED, and Wired Location Service, page 29-10

Understanding LLDP, LLDP-MED, and Wired Location Service

LLDP

The Cisco Discovery Protocol (CDP) is a device discovery protocol that runs over Layer 2 (the data link
layer) on all Cisco-manufactured devices (routers, bridges, access servers, and switches). CDP allows
network management applications to automatically discover and learn about other Cisco devices
connected to the network.

To support non-Cisco devices and to allow for interoperability between other devices, the switch
supports the IEEE 802.1AB Link Layer Discovery Protocol (LLDP). LLDP is a neighbor discovery
protocol that is used for network devices to advertise information about themselves to other devices on
the network. This protocol runs over the data-link layer, which allows two systems running different
network layer protocols to learn about each other.

LLDP supports a set of attributes that it uses to discover neighbor devices. These attributes contain type,
length, and value descriptions and are referred to as TLVs. LLDP supported devices can use TLVs to receive
and send information to their neighbors. This protocol can advertise details such as configuration
information, device capabilities, and device identity.

«
...
675
676
677
678
679
...
»

Содержание Catalyst 3130











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3130

Бренд: IBM Страницы: 2

SecPath F1000-AI-5 Series

Бренд: H3C Страницы: 70

Бренд: Juniper Страницы: 26

Бренд: Billion Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды